I’m installing the Red Line GM evap kit on my 79. I hooked everything up but I cannot find the tank line check valve.
I expected it to be in the access panel near the filler neck and the vapor chamber - but there’s nothing there. I unbolted it leaned it forward and it’s not behind it either...
I am changing my valve cover gasket (OEM Gasket), but the darn thing will not stay in place, every time I try to put the cover back on the gasket falls out, it is too loose. I am putting the long edge into the top of the valve cover so the flatter section would rest against the matting surface...
Hi guys, my 1992 dubai version w/o overdrive 1HD-T valve body comes to a problem as when the shifter is on the R (reverse) position, the vehicle wont move and you have to give more throttle for it to move a little and comes to an abrupt stop after releasing the throttle as if there is a brake on...
I am replacing my valve cover gasket and while wiggling out the Half Moon pieces both of them broke on the outside edge (my luck)......I need to order 2 replacements, can someone help me with a part# or the actual name of the pieces so I can locate them. Searching via "half moon" seems to get me...
I've just replaced the heater control valve, old one was a bit leaky. Now at the max hot setting it only blows hot air for about 10 seconds before it goes lukewarm. If I turn it down to full cold then back to full hot it does the same thing again. Anyone any thoughts as to why it's doing this?
Wondering if anyone has used a product like this before that can replace a valve stem from the outside of the wheel
Running stock wheels, I'm always concerned about getting into an obstacle off-road that could potentially rip the valve stem off. Hasn't happened yet, but I've got enough lip...
Had a valve cover polished to put on my 2F and have grown accustom to the stock finish with threaded cap so this one is up for sale to clear out some space.
Note this is specific to a 75-79 2F as it is the taller valve cover and needs the taller valve cover studs from the earlier motors.
The...
Hi All -
I did review the other posts on the form regarding this prior to install.
I went to replace my valve stem seals today on my 1970 FJ40 (i.e. F155). Got to the first one, and I have two questions.
First, the oem seal is the umbrella type. It is hard as a rock. I am assuming that...
I have a 1978 FJ40 I replaced all fuel lines and have a new metal gas tank. I'm getting a strong gas smell inside the cab. I noticed 75-77 cruisers have an inline check valve going from the tank to the charcoal canister. But I do not see that for the 78's. Is this something I can add that might...
i was hoping to get a better understanding of these two issues. does anyone have any pics or technical information?
do i find both of them in the FSM in the mechanical chapter?
do spark plug tube seals get done when you do a valve stem seals get done when you do a head gasket?
i've got a couple...
I'm pretty sure this valve is 32mm but I can't get any sort of torque on it without it slipping. Does anyone have any tips on how best to get this off?
I have no clue if it matters but it seems like there are two different types with different part numbers. I have a 2007 if it makes any...
Changing the charcoal cannister on my 60 for an A/M model similar to one many others have posted with before. I understand plumbing for the reduction of the 4 vents to the two included on the new A/M cannister and have fresh hoses ready to go.
When taking of the hoses, the Outer vent control...
How often are you guys changing this out. I know it's a maintenance item but do you do it at 30k or what. I need to change the heater tees also. I guess do them both at the same time. and same intervals?
Thanks,
1979 2F engine, D smogged, 91,000 miles, in the middle of replacing valve stem seals, and the replacement seals do not match the original seals on the engine. Been getting white smoke on start up that seems to reduce as temperature of engine reaches normal. More white smoke while driving down...
Good afternoon, just a quick question, does anyone know how many hours Toyota allots for replacing the expansion valve on a 2009? I am being quoted 11 hrs. Thanks
Hi guys,
Using @cruisermatt ‘s vent hose replacement kit and all has gone great with it. I’m chasing a gas smell on the cab issue so figured I’d search for a clogged vent line. All the hoses looked fine, but I stick a very thin screwdriver into one of the metal ports the lower vent hoses attach...
What does the MUD braintrust suggest for R134a valve core replacements and where to best buy them? I've just spent 10 minutes googling for Japanese/Denso replacement valve cores and the best thing I've found was questionable "Denso" valve cores from Ali-Express type website. I've just finished...
I'm in the process of rebuilding a (non-North American) 1989 BJ60. The vehicle was originally equipped with drum brakes on all wheels, so never came with a brake proportioning valve. I am adding a year-correct, factory original brake master cylinder, dual-diaphragm booster and proportioning...