valve

  1. G

    Valve Clicking after Air Intake Manifold removed to replace PHH

    Dealer-maintained FZJ80 Land Cruiser with 1FZ-FE engine has about 100K city/highway miles. I took it to a non-dealer to have PHH replaced. They had to remove the Air Intake Manifold (upper and lower) to replace the PHH (which was bulging and leaking) with an Xtreme Silicone Pesky Heater Hose...
  2. C

    Brake Proportioning Valve

    So as I am finishing up my knuckle rebuild, I put on new brakes. Noticed that my master cylinder was leaking. So i took it off to rebuild it, my question is do I need to do anything the the brake proportioning valve? I bought a rebuild kit for the master, is there anything needed for this...
  3. baldilocks

    For Sale  1993-80 series AC compressor and expansion valve

    I don't know if it works because the AC system had no refrigerant in it when I bought the vehicle and I replaced the entire system before recharging. $20 plus the ride or local pick up in Vacaville, CA.
  4. kilmarkid

    heater control valve blew at 263k miles(EHCV)

    Blew the heater valve.at 263k miles. It was not just brittle, it was toast. Zero integrity. Thought it was the PHH but that turned out to be fine. Replaced the pesky part since most of the fluid was already drained on my driveway. PHH took about 2 hours between cold ones and mucho forearm skin...
  5. B

    HAI Valve Test / Repair / Replace Questions

    Working on my 85 wagon final stages of putting back together after cracked head. I am reconnecting air intake hose and hot air intake hoses long ago removed by the PO. I decided to test the function of the HAI valve by applying vacuum. My HAI valve will actuate momentarily when I apply vacuum...
  6. S

    For Sale  Brake Proportioningredients Valve

    Good working order. $100 obo Item located in South East Texas.
  7. S

    For Sale  FJ40 Brake Proportioning Valve

    This was taken off a running and driving truck sold I know it functions correctly. I have seen these listed for quite a bit of money and really unsure of what it is worth. I'll ask $200 obo to start with as I have seen used ones advertised for $264.00. No sensible offer refused. Thanks
  8. IslandJ

    Wanted  FJ60 Vacuum transmitting valve (Carb)

    Broke mine, looking for a used one.
  9. Devil's Slide Doug

    LSPB valve or Wilwood proportioning valve?

    This topic has been beat to death. My valve works well and doesn't leak and I don't like messing with plumbing. The lift, spring rate, travel, tire size do make the silly spring rod difficult to adjust at best. This was a 1/2 banana "fab" job at worse. I will let the pictures do the rest of the...
  10. Stevesnj

    Tire valve stem hole size

    I just got some new tire and want to get the valve stems but I don't know the stem hole diameter in the wheel. Anyone know what size I should buy?
  11. hidesertfj40

    16" black Steelie with oval hole at valve stem

    Good Afternoon gents, Can anyone here shed some light on the difference between the 16" black steelies with an oval hole at the valve stem vs ones without the oval hole? Is there any significant design change in this rim? Thank you,
  12. fooldall1

    Power Steering Air Control Valve/General PS Question

    Would a bad or failing valve create hard, rapid left to right steering at low RPM (think parallel parking)? Recently replaced Timing/Idler/Tensioner pulleys and belts, rack is two years old (not leaking as far as I can tell), and steering is fine otherwise except for slow speed rapid left/right...
  13. fj40toycruiser

    Heater control valve Servo Motor

    New to the family 1993 fzj80. I am in the process of diagnosing why I have no front heat. I have a solid temp reading on the dash. With the cable disconnected at the firewall the valve feels to move freely. When I removed the radio and disconnected the cable at the servo motor the cable moves...
  14. 450LX

    Valve cover plug seal scoring...

    Im on the process of replacing the valve cover spark plug seals and I noticed I have scored the seal surface in a few areas. Should I be concerned? I forgot to take a picture before I dropped it off at the machine shop to get cleaned (im doing a head gasket) . I was thinking maybe a thin rtv...
  15. W

    Discontinued valve shims

    I tried to go order valve shims at my local dealer, and they're discontinued. I'm not looking for extreme performance like Scottryana's shimless buckets, and although a few others have had good luck with Home I would rather not wait/pay for shipping from australia. I've also looked for nissan...
  16. fj40toycruiser

    For Sale  1HZ Oil Pan to Valve Cover NH

    I have a 1HZ oil pan to valve cover engine core I purchased 4 years ago with the intent to rebuild. Reality has caught up to me and I now realize I have too many other priorities. I can assist with shipping but the details and cost needs to handled by the buyer. I had it shipped from TN to NH...
  17. cruiserhound

    EGR valve replacement or De-Smog?

    I'm still getting to know my cruiser and I'm starting to realize that certain parts might not be available for my 3FE. EGR valve replacement is a scheduled maintenance item and I'm fairly certain my EGR valve hasn't been changed for 243k miles. If she was running great I wouldn't bother with it...
  18. IBFJ62

    Valve Stem Seals. Workbench or Shop?

    So, I'm having to follow up on an earlier issue of not getting oil up to the valve train. Problem solved, but it looks like I cooked the valve stem seals when it wasn't oiling up there. Is replacing the seals a workbench fix, or do I need to drop the head off at a shop and just have them do...
  19. MtnCruiserFZJ80

    Removing the EGR valve

    Hi all, 1994 fzj80 with 238k on the clock. I have been battling the dreaded code 71 on and off over the last few months. I finally got around to removing and replacing the EGR valve, but dang it's tough to get off. I have the 32mm union bolt off, as well as the three bolts/nuts holding it to...
  20. Snowbound

    Valve cover - paint or powder coat?

    Just getting some parts powder coated and wondered about the valve cover. Mine is a 69 F motor so the valve cover is black, or was once. Is powder coat a good idea? And should I do inside and outside or just outside? I have googled it and found some folk saying it can peel off the inside and...
Back
Top Bottom