valve

Does anyone know where I can find an EGR Valve Assembly for a 1991 3FE? It seems it has been discontinued from Toyota. I also tried rockauto and they are out of stock. I'd like a decent quality part.

I have upgraded my 78' FJ45 with a 12HT. I could use some good pictures showing the placement of the H style heater valve. Also is the F style Warm Pull cable a different length than the H style cable or are they all the same? Thanks in advance for all of your help.

Hi guys chasing up the plug to suit my new 12ht shut down VSV valve would anyone have a lead on where to buy this type of plug.

I know this has been mentioned before, but I couldn't find any pictures, and since everyone loves pictures... Since spring has come (once again this year) to North Carolina, I decided to do a little PM/RM on the fleet. Both my '94 and '95 leak over the rear window when I use the windshield...

I could not leave well enough alone and tried to remove the screws holding the butterfly to the shaft. I was able to get them out and might even have enough threads left to put new ones back in. But these screws were staked into the shaft, so does anyone know how to reinstall these screws the...

Good afternoon! I'm preparing to do a valve adjustment on my HDJ and it appears an SST is in order. Its the SST 09248-64011 - called the Valve Clearance Adjustment Tool I'd really like to find someone who could loan or rent me the tool. I'm really good (obsessive) about taking care of tools so...

My flapper was loose on the shaft so I pulled it apart. Does the bend in mine look correct? I temporarily re-installed the flapper in the same orientation I found it. This would be cold Here's hot

Good afternoon! I'm preparing to do a valve adjustment on my HDJ and it appears an SST is in order. Its the SST 09248-64011 - called the Valve Clearance Adjustment Tool I'd really like to find someone who could loan or rent me the tool. I'm really good (obsessive) about taking care of tools...

Title says it all. $50 plus shipping.

So pulling the valve covers off today to change leaking gaskets and checked valve gap on passenger side cyl 2 4 6 8 2000LC with 170,000. Valve Clearance per FSM cold Intake : 0.015mm - 0.025mm 0.006in - 0.010in Exhaust : 0.25mm - 0.35mm 0.010in...

Anyone had this issue? Apparently its common on the Tundras. I really don't want to fool with the dealer. Looking for real personal experience and possible DIY fixes. Thanks!!

Old and dirty ok.

Anybody have any experience with these valve body upgrades from wholesale automatics from Australia any info would be appreciated thanks

Seeking over the phone guidance now. I have her all opened up and feeler guage in hand. Measurements seem odd, some tight, some not. And for the life of me I can not bump my truck to get TDC in the sight window. Its either before or after and is pissing me off. I have both marks lightened up...

In need of some help... so the PO of my truck jerry rigged the throttle valve solenoid on the carb. I'm installing a trollhole carb and need to get this straightened out so I can install the carb and do a valve adjustment. They spliced the solenoid directly into the harness, so I don't have a...

Have a 67 FJ40 with an F block and 2F head...The head gasket went on it..Since I've gotten it back the #5 intake valve nut keeps breaking loose and causing a very loud tick..After adjustment it will run fine for about 50 to 100 miles then break loose again normally after cold startup sometimes...

I have my transmission preheater bypassed since I'm usually offroading in the summer. But recently I finished my gauge cluster and now I can see my transmission temps (sensor is in the trans cooler line before the cooler). I see temps from 80-140, 140 is only when really getting after it or...

I have another thread on a sludge issue that I have with my 3fe . Then I found out it had coolant leaking from the valve seat . I was trying to figure this all out . If the valve seat is leaking coolant doesn't that mean that the cylinder below it should be full of coolant ? I don't quite...

Hey Guys, I have read through a bunch of threads on this topic but can't seem to find the simple answer. I have a 79 FJ40 with front discs and drum rear, recently I have been noticing when I have to lay into the brakes the rear drums lock up pretty easily. I know there is a stock proportioning...

Anyone have a recommendation for a replacement for the undercarriage spray nozzle (aka OEM radiator drain valve)? I would like a petcock, thumbscrew type preferably, with a 90° fitting I could stick a hose on and then run into a coolant can.