turbo

I heard an unusual noise in my 13B engine that started relatively suddenly. It does have an after market turbo…if that matters. I pulled the valve cover and found these unattached laying freely inside. What are they? Thanks

I'm in the process of solving two minor issues with the turbo and It's been running flawlessly. I think I have excessive PCV going into the intake of the compressor, which is making its way down the gullet after coating the compressor fins. I'm able to clean the fins easily but this is...

https://www.toyotarvforsale.com/1976-chinook-in-bozeman-mt/

Sadly I never got around to putting this on my bandi. It's a Complete turbo setup for the om314 mercedes powered bandierante. $2000

Turbo emblems: 60/70/80 series for sale…

If you’re looking for an insanely fun turbo Land Cruiser you’re in the right place. If you’re looking for a comfy daily driver, I’d keep looking. I built this truck as an exercise in what you could do with a rough starting point, elbow grease and a lot of parts. It wasn’t built for comfort...

Sam dynoed his turbo 1fz and hit over 1k hp at the hubs.

I installed a mamba ct26 turbo on my 1hd-ft and realized that I didn’t adjust the preload correctly. Is there a way to change the preload without taking the turbo off?

Since the Turbo Owners thread is locked, I am posting a new thread. I opened the the hood today (pre-trip) discovered oil residue on the exterior bottom of the compressor housing. I’ve had no issues for 2+ years (<10k miles) so I don’t imagine there’s an issue with the turbo bearings...

It sits in the back of my mind that when one day I can afford to replace the old nearly 700 k km 1hz in my 80 I'd like another 1hz not a 1hdt and fit a turbo kit myself. But there are plenty of offerings - DTS, HP Diesel, etc. Being a pleb with no turbo diesel experience they all basically look...

I have recently fit a turbo tap / boost tee to my 1996 land cruiser it now makes a futter constantly even at 8psi just cruising. Just to clarify nothing has been done other than turned up fuel and boost at 16/17 psi and a plastic snorkel. I can't turn my PSI down from those numbers is my boost...

Which one of you is going to figure out how to swap in the 3.4L I-Force Max Hybrid into an 80? Go ahead and throw the 10 speed transmission in there too.

Anyone have a used turbo exhaust elbow from an FTE laying around(turns basically 90 deg to the rear and down)? I know I can buy new but hoping for cheaper/faster as used... TIA

Looking to buy a compete Witt’s end turbo or factory supercharger kit. Just seeing what’s out there.

I don’t post very often and typically ask questions that have been asked a million times but… I would like to know if anyone has any experience with installing either a turbo or a supercharger on the LC 200 (‘18) gas V8. I have 33x10.5 BFG KO2 on 2” Ikon lift and pull an 12’ enclosed trailer on...

Hello guys I'm new over here and I have a project a bj40 1978 currently refreshing the engine (B engine) I am stroking the engine to the 2b specs 3.2 And I want to add a turbo on it which turbo set up would you recommend me? Thank you very much and it's a pleasure to be in this forum. I am from...

Year: 1992 Model: HZJ80 Eurospec Imported from Belgium. Used as a NATO truck Miles: 259k kilometers (161k miles) Features: Poverty pack model: manual windows manual door locks barn doors vinyl carpet, jute padding, and noise dampener on the floor. no sunroof Simplified gauge cluster Cloth...

I picked up an Elate Mfg FDFI1900 supercharger kit last year and installed it over the last few days. This is now the final mod of my Super Cruiser build :steer: I went for the full enchilada and ordered the intercooled kit for my VVTI 2UZ. I think I am the first person in the USA to put one of...

Running a Gt2052 with an adapter plate to a 13bt Manifold .Having a hard time locating the right gaskets, previous owner used that high temp paper gasket material but it doesn't seem to hold up well. Should I just make some out of copper ? get everything machined flat and use no gaskets ? or if...

Hi, I bought my 3rd HDJ80 this time a 12 valve (manual, 3rd row seats). Whilst it works well I am doing a frame off restoration to get it back to as new condition as possible. Everything will be kept original except some performance enhancements. So this question is about turbos. Would there...