Wasn't leaking when I took engine out two years ago, why would this suddenly be leaking?
What am I in for in terms of fixing this myself, full dissasmebly? can one "ignore" a common leak like this? Here's a free pic of my finger covered with what is on there (youll have to pay for pics of full...
I have a split transfer case and am putting it together. The shift lever going to the shift fork operates correctly until I tighten the shift detent ball/spring/bolt on the top of the case down and then it’s not shifting as it should. (It’s like it’s locking up the shift fork). Anyone have any...
I just replaced the transfer case shift lever seat in my '93 4WD 4-Runner with the manual transmission. I'm having a lot of trouble holding down the metal cover against the force of the spring so I can install the retainer clip. Are there any tips and/or special tools that will make this easier?
I am getting this fault code, and I am searching for the correct switch sensor to replace on the transfer case? Any direct knowledge on this error code? Also, getting PRNDL switch fault as well, but I think that’s tied into the A/TP warning light I’m getting.
Hi,
I have a FZJ105 and I am about to install a H152 box from a 2008 VDJ79.
I will be installing a taller 5th gearset.
Will the transfer case from the FZJ105 bolt up to the H152?
If not is it possible and what must be done?
Thank you
Tranfercase swap question. I am rebuilding my FJ40 75 (12/74) 4 speed, but I have some issues with the 4 speed transfer case. I have a 3 speed transfer case that is rebuilt and ready to go I got in trade. The input bearing is 29 tooth with 10 spline in the transfer and mine has a 29 tooth 16...
Hello all, in research today it looks like I have found this aisin part #. SAT 012. Can any techs confirm this is the OE part lexus would sell for the transfer case actuator? It's listing between 4 and 500, vs the 1200 for the part. Hope this can save some one some money if we can confirm it. Cheers
Hello all, a buddy of mine just purchased an 04 gx470 with 280k on the clock. Looks like it has the dreaded actuator leak, slee has quoted 4k to fix. Has anyone in the area done the reseal job and can provide guidance?
Come this Monday I will bringing home a 73 FJ 40 it's a bit rough but has some good modifications to it. The motor is a small block 350 Chevy the transmission is cast iron and looks to possibly be an SM 420 and the transfer case is most likely stock. The seller bought the rig as a fixer upper...
Selling a complete nosecone removed from a 77 FJ40 transfer case. Looks to be in good shape it came from a running truck many years ago. I've seen a few of these break on the trail including on my truck when my driveshaft refused to telescope in (don't ask why) and the nose cone broke badly...
Doing a little TLC tonight and noticed the ground strap…..well ain’t doing it’s job !!! 🫤 I looked but couldn‘t see where the heck this thing was supposed to be grounded to. Can someone point out the other end attachment location and I would assume a thick piece of insulated wire ( like a...
Hello everyone, couple of issues I hope somebody can provide me with some input. Have a FJ40 with a orion transfer need to find a speedi sleeve for the park brake hub since it was leaking ,question does anyone knows the correct speedi sleeve to use and recommendations as to were to acquire and...
The Japanese transfer case instruction decal is NLA. It sits on the glove box door and looks like this, but it's less blurry in real life.
If anyone has this decal, could you post a super clear photo of it? I am going to make some.
Thank you.
Hello there, if possible if any knows about serious differences between HJ45 1979 transfer versus 1980 HJ45 transfer, somebody told me that 1980 HJ45 comes with reinforced transfer but now, there are anybody who kindly post knowledge about this ? thanks in advance.!
That perennial question 8-)
I currently run Caltex VMX-M in both the 5-spd manual box (with Nulon G-70) and part-time transfer case (with no additive) of my 80. Looking to try something else.
I've had recommendations to firstly not use the same oil in both and secondly to go with Redline MT-90...
Anyone with a HF1A (part-time) transfer case done a self-rebuild on theirs? Mine is I think original to the vehicle. It's got a wobbly rear output flange so that means it's at the point of needing proper attention.
I can get a rebuild kit. I've never pulled a transfer case apart but would there...
Selling this T-Case Lever from an FJ62
Sleeved brass bushings added to the shift points
no rubber bushings needed, works really well
$60.00 + whatever shipping
Please PM
Hey everyone,
So I was on the beach trying to surf the other day. Got stuck in the sand. I did not have 4WD engaged, but the right rear wheel still kept taking all the power though. The only wheel that moved was that one. I had the differential lock engaged in the front, but no 4WD. Am I...