transfer

I've just noticed a small puddle of oil under my 2002 LX470. Looks like the leak is at the Drain Plug on the Transfer Case. I assume this is the Transfer Case? See photo. In the photo have I identified the fill plug? What oil do I need? I assume I just open the fill plug and pump in some more...

Anybody know what causes the intermediate shift lever to bend in transfer case? I rebuild this case 10 years ago from a parts 40, and went to install it today. Couldn't get the shifter to work with the gate. Finally removed some parts from a working rig and noticed the bend. Nothing was noted...

3 spd. Transmission and transfer case, with floor shift, from 74' FJ40. In good working order $500. Near Lincoln NE.

I have a 1996 80 series, 115k miles, lockers. I bought the truck a few months ago and added a OME 2.5'' lift kit with caster correction kit & 1'' Manofre Spacer in front. I had a shop install the lift. immediately after lift install I was getting the GRRRR sound while accelerating/decelerating...

4 speed Transmission mated to 3 speed transfer case --- $250 pick up only located in Bowling Green, KY

Converting from a 3 speed to a 4 speed trans...keeping my 3 speed transfer...need the PTO spacer or gear for the 4 speed trans. Not running a PTO on this truck so spacer is fine.

Hi all, I have a 3 speed auto tranny that appears to be leaking into the transfer case. Checked transfer this afternoon and it was overfilled with a mix of atf and gear oil. Mostly atf. I read on the web that I need to change some seals just don't know which one(s). Here's some pics to show...

1997 Land Cruiser I just installed the 3-inch HD OME lift. Looks great and feels smooth but I have a grinding sound/vibration at high speeds (65mph+) and especially audible when I release the gas from high speeds. I initially thought driveline angle issue after lifting it but would a 3-inch...

I've got a 3 speed case mated to an H41 4 speed trans. I have the shift lever and bracket that mounts to the transmission. I also have the arm that runs down the nose cone. What I need is the linkage parts that run from the arm on top of the transfer case to the shift lever. I think these...

Doing a 4speed trans to a 3 speed transfer for my 45LV build....need the 4 speed transfer output assembly and the floor linkage for the 4 speed transfer.

1977 FJ40 4 Speed and Transfer case. Worked when pulled. A little dirty, but should be good for someone elses project. $600 OBO Located in Steamboat Springs, CO

Anybody got a source for a transfer case for an 81 fj40? I'm in Tucson

Needed in Tucson AZ 85750. Would consider tranny/xfer combo. PM please

I'm considering going with an Atlas and am looking for some feedback from Atlas owners. I have a 99 Taco with a D44 front and 4:88's with a stock auto and stock case on 35's (37's might be in the future). I wheel the Rubicon and Moab a lot and have to ride the brakes (disc all around) to make...

I have a 2001 Transfer Case, has 156k miles on it, with wiring harness and gasket kit (04362-60080) will ship anywhere in the continental US. The Transfer case had a leak coming from the front housing and I don't have the time or experience to open up the case and replace the seals and see if...

This truck is in a part out thread but I thought I would post here also since not everybody goes there. This is a 1985 2F and 4 SPD transmission and split transfer case out of a 1985 FJ60. 115k on the odometer. It runs and drives right now.. I'm selling it complete from the fan back just as...

H42 tranny not H41-Came out of a USA 1983 FJ60 with 250K miles. Removed from truck in '07. Tranny and transfer shifted fine, no unusual noised, all ranges working. Very little wear on input shaft splines. 34mm idler shaft. Stored in heated garage since pulled. $400.

H42 tranny not H41-Came out of USA 1983 FJ60 with 250K miles. Removed from truck in '07. Tranny shifted fine, no unusual noises, no major leaks at that time. Shows very little wear on input shaft splines.Transfer shifted fine, all ranges engaged. Kept in a heated garage since pulled. $400.

I had great expectations and plans to put a SM420 into my FJ40. But, alas, life has taken a different turn and I have headed in a different direction with 40. What does this mean for you - if you want to undertake the project, I am offering a smoking hot deal on this entire setup. Some assembly...

Specifically, the front output housing - managed to drop mine off the bench, hit the concrete perfectly and took a chunk out of the seal area. Please please PM if you've got parts laying around.