I wrote somewhere in this forum some time back that I will get back to an 80 and here I am, when I sold my previous one I thought I would move on, but I did not get enough.
Found a gem, 1997: in good condition for the price, and most importantly it has a freshly rebuilt GEN 2 1FZ-FE equipped...
Good afternoon everyone,
I recently purchased a 2002 Land Cruiser that had great service records, and was well maintained (or at least I thought so.) I'm has 225k miles on it, and runs well. I was looking over some service records, and found the original owners phone number, so I reached out to...
Hey guys - haven’t posted in this forum in a while as I’ve had good luck - until now.
1988 Aussie HJ75 - put it in 4H to get it in the boat garage out back. Parked it and after 5 minutes or so, I noticed a lot of gear oil puked out from the t-case. Goes in and out of 4WD just fine. Haven’t...
Hello all.
Banging noise coming from front output shaft area. A couple question?.
Any ideas?
can I separate the front output cone from case to inspect where the issue is or would it be better to just pull the whole case? Would you pull trans and case together or just pull the case?
Thank...
I am getting close to wrapping up a vortec swap in my 62, and have noticed some odd behavior from my transfer case. Wondering if anyone has a recommendation, or experience with something similar.
Basically it seems like the 4l60 doesn't stop spinning enough for the transfer case to be shifted...
This was mated to a 3-on-tree 3 speed. Came out of a 1965 FJ40.
$400 + shipping OBO
I get decent shipping rates but I’d really rather not ship this. We can quote it out but except it to still be pretty expensive due to weight.
I'm aiming to rebuild my case next spring. 83 FJ60. Currently have a 4spd/stock case/stock diffs rolling 33x10.50r15s.
I plan to keep the 2F/4spd until they blow. It runs great now and hopefully with some preventative maintiance we should be in the clear for a while. Future plans will be...
Looking for a decent crankshaft. Going to be getting machined so condition not a concern as long as it hasn’t spun a bearing too bad and isn’t super rusty on seal surface.
Also if someone has a junk crankshaft please reach out as well as I have uses for that too.
Have two 3-speed transmission/transfer cases.
One is column shift from a 67, the other is floor shift (converted with what I believe is the OEM top cover)
Neither have parking brake drum or backing plate.
Both are cores, condition unknown.
Asking $200 for each.
Can ship anywhere.
Guys, while removing the rear section of my transfer case on my '97 FZJ80 to eliminate the viscous Coupler, the case section fell over and broke a switch (I think that's what it is, it looks like it might be the indicator if the locker actuator is engaged, maybe?). I couldn't get an arrow on...
wanted to consult the experts on something that has me stumped.
executive summary - I accidentally shifted my '68 into FWD, and then couldn't get it back to 2WD. tested vacuum lines and they are working. replaced them anyway with new just in case. it certainly appears as the vacuum shifter on...
In need of help TIA, Few key details so please keep eye out.
So my Landrover Series 3 has a toyota 3B, gearbox and transfercase etc. I'm currently doing a as I go restoration. Currently I am trying to get my handbrake working again as it stopped working a few months ago.
When I originally did...
We were doing 5 Speed swap on FJ62 and ordered this kit. The idler shaft diameter is smaller. So we ordered a new kit and can't return this one.
I took a picture of the kit and number. Please do your research. Make me an offer.
I bought a used transfer case from CruiserParts with plans to do an ultra low range swap. My plans have changed and I am no longer going to go this route. Does not include with sensors or CDL motor. One of the studs on the rear output is spinning which would need to be addressed before...
Suddenly getting a metallic noise from the transfer case shifter. Check out the video below. I can even feel a corresponding vibration on the TC shifter when I hear it. Checked both the TC and transmission oil and I'm good. Thoughts?
Been chasing a loud whine in transfer case along with a fair bit of slop/lash. I just started pulling it apart and it appears that the output gear splines are pretty loose on the shaft. I have heard that the output gears and bearings are not supposed to be tight on the output shaft, but this...
I have for sale a new unused Terrain Tamer TK4 transfer case overhaul kit. It is used on Land Cruiser transfer cases from 7/80-10/85. All parts are present when compared to the Terrain Tamer website. Message me with any questions. $85