I have a full time transfer case and would like to convert it to the viscous coupling type. Can I just unbolt the housing from the transfer case, and fit it along with the vc to my hf2a or are there other internal differences?
Hi guys, thank you for understanding for beginner!
Until rebuild my transfer case HF1A i have some trouble-missunderstanding about one part.
I see this pin on the diagram but can not find in manual, should be instal it or not ?
Can sombody explain ?
Thank you so much
Dave
Hi
I searched the forum and found some conflicting information. My transfer case fill plug is stripped so I need to buy a new one. Does anyone know the part numbers? I have 90341-18039 for the fill plug? is this correct or is there an alternate part number? Does anyone have the drain plug...
Hey Dudes,
I was lucky enough to partner with an expert in the industry to bring you guys a 4-Part series showing how to rebuild and modify the HF2AV transfer case. The expert I'm talking about is Georg Esterer @orangefj45 who owns Valley Hybrids in Stockton, California. Georg's Valley Hybrids...
Hey Dudes,
I was lucky enough to partner with an expert in the industry to bring you guys a 4-Part series showing how to rebuild and modify the HF2AV transfer case. The expert I'm talking about is Georg Esterer @orangefj45 who owns Valley Hybrids in Stockton, California. Georg's Valley...
While trying to figure out a T-case shifter bracket from my 4L80 to T-case I'm now questioning how the H-N-L operates. I see if you do a twin stick you need a different 2h-4h shift rod but wondering why? How does it affect the H-N-L shift lever? I can move the H_N_L lever no matter what...
I conquered the front DS clearance issue, but have been struggling with getting the TC shifter to function. I have built several types of mounts off of the trans for the factory shifter, but just can't seem to get the H-N-L portion to function appropriately. For those who have tackled this, do...
Looking for an early model transfer case shifter retainer and shaft (PN: 36344-60021), the pic should show exactly what I am looking for, it's needed for the LT swap kit I have from @torfab
Any questions please let me know. Thanks.
The vehicle is a 1997 FZJ80 with an HF2F installed as a replacement for the HF2AV. I did this about 10 years ago, I have a vague memory the drive shafts were different lengths. Due to a maintenace brain fault, I neglected to grease the splines (yes !! I neglected to do that. ) and now the shaft...
Up for sale or trade is a 3 on the tree transmission and attached transfercase from my 1971 FJ40. Believe it is in good working order but was never able to test it out. 1F blew head gasket and a 4 speed 2F was swapped in. Open to trades for fj40-fj60 parts also. Make offer shoot me a message!
Offering up the transfer case off of my 100. It is more than likely in need of a rebuild. The front puts out shaft studs are stripped and need replacing. The case leaks at the front output flange as well. Great for someone who wants to re-gear without having much downtime. Can ship at buyers...
I'm going to pull apart a transfer case shortly to install sumo low gears and am wondering if there are any tricks to getting red FIPG to release?
I've had two other transfer cases apart this year and the FIPG combined with corrosion has made it a lot of work, and no shortage of cursing. Much...
I've got a full powertrain out of a 1972. F Motor, 3 speed, and transfer case ($600). Motor will need a rebuild. Also have another freshly milled F block ($200) and a Weber carb ($200) for sale. Can ship the Carb. Pickup only for the powertrain. Thanks
Have a nice clean transfer case came from a 96 80 series with 166K on the odometer. Worked great, is clean as there were no leaks under the truck. Comes with the shifter too. $250 located northeast PA. A perfect candidate in which you can install the lower/higher gear sets while your truck is...