transfer case

I've got a 1991 FJ80 that needs a transfer case. I am starting to think The Amish Electrician keeps the HF2A transfer cases with the hen's teeth. I'm wondering if there is anything I need to know about fitment. Is there any difference in the transfer case depending upon engine? This one...

Came out of a 1998 Lexus LX470 with 411,000 miles on it (at time of removal). The case had been filled with ATF and the gears are so worn out that they vibrate above speeds of 45 mph. Good candidate for a regear or rebuild. Plenty of good spare parts Asking $200 willing to negotiate

25.00 plus shipping.

Misc FJ80 parts from 1994 FJ80 and 1996 LX450. Including nearly rust free body for the LX

Toyota dealer can’t get the studs in for over a week (part 9011411003). Searching rock auto and the oreillys website yields zero results, but does anyone happen to know a Dorman or other aftermarket part number for the output flange studs? Thanks!

Have a transmission and transfer case from a 96 80 series with 167K on the clock. Everything worked as it should prior to removal. I still haven't separated them so let's say $350 for the entire unit and that includes the torque converter and the transfer case shifter. Transmission or transfer...

Hi everyone! I have a 99' land cruiser, and live at the bottom of one of the steepest roads in america. The other day, I was driving up the hill when the transfer case failed (sudden grinding sound, can't put in gear in either high or low). I managed to back it down the hill to a safe flat...

Bought this idler shaft from AA and never ended up using it. Box was only opened for pictures. Located in Castaic Ca. Part number and description in the pictures. 125 shipped to lower 48.

I pulled my TC out, due to the front loosing tension and causing clunk and jerk. Actuator and other sensor are sill good. Mileage is around 182k. Prefer local pick up or I can meet at resonable distance.

Team, I am in process of rebuilding my 5/77 2F transfer case rear output seal and e-brake components. I do not have a FSM handy, was hoping you can help here (see pic). Also, here are the callouts: 1. Rear u joint bolts (4) torque spec 2. Output shaft stake nut (1) torque spec 3. Front u...

I wrote somewhere in this forum some time back that I will get back to an 80 and here I am, when I sold my previous one I thought I would move on, but I did not get enough. Found a gem, 1997: in good condition for the price, and most importantly it has a freshly rebuilt GEN 2 1FZ-FE equipped...

Looking for a good used FZJ80/LX450 CDL

Good afternoon everyone, I recently purchased a 2002 Land Cruiser that had great service records, and was well maintained (or at least I thought so.) I'm has 225k miles on it, and runs well. I was looking over some service records, and found the original owners phone number, so I reached out to...

Hey guys - haven’t posted in this forum in a while as I’ve had good luck - until now. 1988 Aussie HJ75 - put it in 4H to get it in the boat garage out back. Parked it and after 5 minutes or so, I noticed a lot of gear oil puked out from the t-case. Goes in and out of 4WD just fine. Haven’t...

Hello all. Banging noise coming from front output shaft area. A couple question?. Any ideas? can I separate the front output cone from case to inspect where the issue is or would it be better to just pull the whole case? Would you pull trans and case together or just pull the case? Thank...

I am getting close to wrapping up a vortec swap in my 62, and have noticed some odd behavior from my transfer case. Wondering if anyone has a recommendation, or experience with something similar. Basically it seems like the 4l60 doesn't stop spinning enough for the transfer case to be shifted...

This was mated to a 3-on-tree 3 speed. Came out of a 1965 FJ40. $400 + shipping OBO I get decent shipping rates but I’d really rather not ship this. We can quote it out but except it to still be pretty expensive due to weight.

Anyone have an Orion Transfer case they're willing to part with? UPDATE: I bought a new one.

Same as title , looking for SC for 3.4.. willing to pay for shipping or travel, also not willing to overpay for one … don’t need one THAT bad

I'm aiming to rebuild my case next spring. 83 FJ60. Currently have a 4spd/stock case/stock diffs rolling 33x10.50r15s. I plan to keep the 2F/4spd until they blow. It runs great now and hopefully with some preventative maintiance we should be in the clear for a while. Future plans will be...