Since no one has a rebuild kit and the only thing I can find close is a couple of misc parts from SOR for $120 (!) I'm wondering if it's possible to swap a later model center arm onto my 67 frame. I know the mount looks different. Every Cruiser parts seller out there has the later model rebuild...
I'm starting this thread to document the parts, costs and work done, as fully as possible. Ill be adding info as I go along. Im doing all work myself except for the manifold back exhaust. Work will begin in March 2024 and be finished in time for our trip to Ouray in July 2024. This by no means...
Back Ground:
Every November is our annual trip to Pismo Beach, CA. This started more than twenty years ago as the Surf n Turf Land Cruiser party. A four day event playing in the sand with every type of Toyota Land Cruiser/Pickup. It then morphed into Turf n Surf when the founder Jim Brantly...
Hello all, I have recently been tasked with LS swapping my dad's 78 Landcruiser. I have been looking into it a lot, having a little trouble finding help online. Has anyone been through this process that could offer some tips? I looked for a thread discussing it but could not find one, if I am...
FJ40 with end to end Lexus GS300 + Aristo 2JZ-GTE mod.
Big Single HX40 Super turbo converted
Auto transmission & Manual Mode with Steering E shift
4x4
1992 Landcruiser 70 Driveline
Steel braided AN fuel lines
Oil cooler
Transmission oil cooler
WARN PowerStation winch
3 inch stainless steel...
Was lucky enough to find a healthy running 3b motor and now I have mission of pulling my old one out. My question is, is there any bits and pieces (that arnt entirely obvious) that I'll need for the swap.
Hi all, I'm going to convert my 94 KZN130 1KZTE auto to manual. I have a 5 speed trans, cross member, front and rear driveshafts from a NA 3.0 4Runner, and I am sourcing a r150/1kz bellhousing, fork assembly, flywheel, clutch, pedal box, and clutch slave/master from Australia. The only thing I'm...
I have a 97 LC with an engine that may need swapped out. If I were to source a JDM spec motor from landcruiser heaven would it be a simple “one for one” swap or would I run into wiring harness and electrical readout issues since the JDM spec motor does not have an ERG ?
I dont really have a build thread for my truck or anything, but made this thread so im not just spaming the "what did you do with your 60 this weekend" thread.
This will just be stuff for my @TRAIL TAILOR coil conversion done in my garage at my house. Photos, questions, etc. Thought it would be...
I love my dash box but didn't care for the key lock, something else to carry/lose and required to close the dash box lid. I often lock my keys in the dash box when I'm parked for a mountain bike ride or a run.
My wife's new bronco came with the security console option that has a nice cam...
I wanted to swap the sombreros between to grill to get the better one on my truck but I ended up breaking the plastic pin trying to pry the retainer off.
Clearly there must be a non-destructive technique to do this. Anyone know it?
2008 Cadillac Esclade 6.2L all aluminum L92 engine. Highly sought after complete L92 engine with good ECM included. Engine was pulled from running and driving 2008 Escalade with 114K miles on it in May 2023. Engine ran strong, made no noise and did not burn oil.
Bought this with plans of...
Found a 1997 FJ80 that blew up its engine a few years ago. The old owner couldent afford to do the rebuild on the engine so I took it off his hands last year and have been working on the truck with the help of my mechanic/friend for the last year.
I plan on posting the entire build on here over...
Hey how’s it going
I’ve bought a 1hdt to replace the 1pz in my 77 series and am considering my gearbox options.
Will an h151f from an 80 fit in the transmission tunnel fine? I’m assuming I will have to do some fabrication regarding the crossmembers and lengths of drive shafts?
Or has anyone used...
Hey anyone doing clean,correct LS Swaps in Atlanta? I am looking to do a 6.2 8l90 swap. I am picking up motor and trans this week. ECM TCM etc. thanks for the help!!
I just got a set of rock warrior wheels with tires. I will need to move TPMS sensors from OEM wheels to the RWs.
Question,
1) would any random wheel/tire shop able to handle RW installation (including swap in the TPMS sensors)? I ordered McGard lug nuts and tool set. I know there is a PDF with...
Hi All
I am considering doing the IFS swap on my Diesel 200. I am concerned with the front spring rate # and front shock valving. The reason for this is that the 3UR 5.7 gas engine weighs around 485 lbs. while the 1VD 4.5 diesel weighs in a whopping 822 lbs.
Current Setup
Stock IFS
Front -...
I've had this Warn 12k winch for 16 years, bought it new and it has worked well over the years except the last time I put it use. I had an extra Albright contactor on the shelf and wired that in using the diagram from this thread Warn 5 Pin socket wiring New and Old colors wiring Albright -...