rebuild

I am selling a 2F Remanufactured (Reman) Long block: Powertrain Direct description, “TOYOTA 2F COMP ENGINE 81-87. 4230CC. WITH AIR. WITH POWER STEERING. 8 BOLTS TOTAL FOR INTAKE & EXHAUST”. Long story short, I purchased an 85 Landy out of Billings MT two years ago, the cruiser had about 2k...

I know, I should pay more attention it's been discussed before... I need someone to rebuild a california 1978 carburetor that is disassembled in a box. Don't ask any questions, I don't wish to discuss the details. Lol Anyone out there that does good work without laughing at me? (I couldn't do it!)

Early - 6/1969 Steering Center Arm Wanted to post up a thread on the partial rebuild of my center arm. I say partial because my center arm shaft and the bearing races were undamaged. If you need a new shaft I think that Mark's Off Road and Cruiser Outfitters still have some. If the races...

Hi guys, I have 88 single cab 22re 4x4. Its has 265k on its original engine and the timing cover recently started leaking/cracked equalling milky oil. I had decided to rebuild the 22re myself but a neighbor down the road just offered me a complete 93 pickup 22re 2wd with 170k that was...

My truck came from Virginia, and Michigan before that with lackluster maintenance history. I am rebuilding the front axles now and am stuck trying to decide what I should I do about these pitted swivel balls. I cleaned them up the best I could and used some rust converter on them. I am trying...

Hey there guys, I'm a pretty new member here, but I've been looking through the forums for months now. Searching for some help/advice on my project, so I'm going to go ahead and list all of the parts that have been replaced or restored and other misc work that has been done. New • KYB monotubes...

I'm going to be starting my axle rebuild tonight and ran into another FJ80 owner who said something about rebuilding the actual birf's. I'm planning on removing the axle from the birf and cleaning the old grease out (haven't determined if I'll need to tear apart the birf for cleaning). The...

New member but long time reader of IH8MUD. I'm currently rebuilding a 1989 HJ75 (2H) and am after ideas on DIY roof lining. Looking at putting some kind of insulation in too as I live in the tropical heat of Far North Queensland, Australia. Has anyone done their own insulation/lining? I...

Ok, I have a situation with my truck and I need some advice and opinions. I've gotten some, but since I have a bit of time before making a final decision, thought I'd get some more. I have a 1980 BJ40 with a B engine. I've only owned it for about 3 years, and it was not exceptionally well taken...

Hi- Y'all have been HUGE helps in the past- and I'm hoping you can help now. I'm not posting in the body/paint forum, as there doesn't seem to be much along this line and this is 100 series specific- I did do a lot of searching first (and would be grateful if anyone here has some other...

History: My brakes are "spongy" for lack of a better word. The pedal depresses almost to the floor and then there is slight resistance for a few inches before the brakes engage. Over these few inches of resistance, the pedal travel is spongy and at no time "firm". I replaced all soft lines...

I have a 92 4.2L 1HDJ-80L Diesel motor in my unit. it currently has 284,000K on it and looking to see when it might to start have problems. No leaks anywhere to be seen, stays the same oil level between changes or cant tell to the naked eye. Mainly road miles, and a little light off roading...

Just checking to see of anything new had happened for ecu's for the 80. Most were "wire on your own" as of a couple of years ago with the exception pf Wolf from AU. Not much feedback on that one though. Haltech has been highly regarded, but not sure if they are wire in or plug and play yet...

So I recently rebuilt the birf and stuck new(er) joints in the rig. The drivers side kinda makes a slapping sound when I hit a bump. Link to video: I hit the top sidewall and it induces the clicking, but the front and back does not. The bottom does to some extent. Am I paranoid or is this...

Well time to start a file to share for my BJ42 LX rebuild. I have started to pull a few of the panels off already and preparing them for painting. Roof has come off and has been sanded down. Just ordered a new headliner, rain gutter and windshield cap from CCOT so that the roof can be completed.

$4500.00 QUOTE TO REBUILD. I FOUND A USED ONE IN GOOD CONDITION FOR $1200.00. THOUGHTS AND INPUT ANYONE. I'M LOCATED IN NORTHERN CALIFORNIA. 1989 FJ62 WITH 232,000 MILES

Hey Folks! Just put in a rebuilt 1FZ and overhauled the tranny. All is together and running smoothly, however there is a slight drop in RPM's when I let of the gas at 2k RPM or above (under load) and the check engine light flashes. It has stalled from this twice. I'm thinking the belts could be...

and.. she's alive! What an experience, long but rewarding! First start vid:

These are still new in the box. Thought I'd need them but the diff turned out to be fine. DIFFERENTIAL OVERHAUL KIT FJ40/55/60, F&R applications, 45mm carrier bearing Toyota Land Cruiser 9.5″ 4.10 Ring & Pinion by NITRO Toyota Land Cruiser 9.5" 4.10 Ring & Pinion by NITRO Purchased for $400...

I have an FZJ80 as most know, It came with a S/C on a rebuilt motor. The S/C only has 45k thru her but Im already thinking about arts for when the time comes and I cannot find any info on it. Im told its NLA