question

I'm wanting a little rumble exhaust sound and don't want to spend the money for a DT exhaust system. Has anyone done a muffler delete? any problems with this? Also thinking about a Flomaster muffler but not sure the route I want to go. My 100 is not my DD so not worried about getting tired of...

Long-time member here but I'm in the 80-Series section. Kicking around a 2nd Gen Sequoia 5.7. Trying to figure out if the myriad of Tundra rims will fit right up to the 2nd Gen Sequoia without needing spacers so it doesn't look awkward, etc. Specifically, the Tundra rims below. Thanks. Mark.

My trucks springs are flat. Truck had what I thought was an after market 2 inch lift. Bought light duty OME leaf springs and now catching hell getting them reinstalled. It is close but I can't get front of spring close to front shackle mount. Did I need to replace shackles? Adjust the...

Needed some help. I replaced all door speakers and wanted to replace the rear sun with a 2way 6 1/2 speaker like the one i put in the front doors. The truck came with a double din and i believe the factory amps are still hooked up. I installed one of the other speaker to try out the sub out put...

Hi Guys, Been reading on the forum about which transmission fluid to use and just needed some clarification before I perform a quick drain and refill on my 2001 LC. According to this TSB - http://toyota-club.net/files/2010/tsb_tc001-02.pdf This is the type of Transmission Fluid I should be...

is the front IFS same parts as a Tundra? Would front coilovers for a Tundra be a direct swap for Sequoias? Or would you need to swap out LCA, UCA, CVs... like some of the 200 series guys do. Or they maybe completely different but that would be very un-toyota like. havent seen this discussed...

Can the community help me decide is this truck a nightmare waiting to happen OR is it a surprising find from the worst place to source cars (Manhattan). A link to 12 total in a Google album - https://goo.gl/photos/toEvWY3z5BTzzVjF6

I'm doing the mini-truck power steering conversion on my '75 FJ40 and have gathered all the parts that I believe I will need. I've read romer's thread and it was very helpful. Just wanted to make sure I have everything before I start so I don't have to make trips to the parts store or...

My '66 FJ40 hasn't had a high beam indicator in the dash for a long time. When I was working on the light switch recently, I realized that someone had run both the RY and RW wires to the headlight terminal on the switch. Looking at the writing diagram, it looks like RW should be hooked up, but...

Hey all, I'm just doing a sanity check on my 2000 LC.. It was well maintained prior to my ownership. I was setting up a weekend to change out the drive shaft ujoints (clunk in drive and squeak in reverse) And I checked the front wheel bearing doing the 6 -- 12 push/pull and when cold there is...

Howdy, all! I am wanting to replace my current antenna with a stock (or stock-looking) antenna. I bought my cruiser w/ this antenna, and don't really like the look of it. A few questions... How hard is it to replace the antenna? I have absolutely NO skills whatsoever when it comes to...

Hi Guys, I have decided to install an OME nitro-charger option on my truck. I'm thinking Slee stock kit, with 2702 front and 2722 rear. This is a 2" increase in the front and .75" in the rear. I have three questions: First - With this set-up, can I still install the Toyota front struts spacer...

I just completed the install of a nice Vintage Air system in my 1973 FJ40. I am not getting hardly any air flow out of the pictured vents. Adjusting the defrost/floor pull switch does not seem to do much of anything. Tons of air comes out by the feet, not so much at these vents. Those of you...

I was towing a 5,000 lb trailer through some hills in Austin over the weekend with the O/D off. Climbing those hills it can only manage about 35 MPH @ 3,000 RPM. I can rev it to 4,000 RPM to pick up some speed but I didn't feel comfortable revving it that high for more than a few seconds. Two...

I've read a few threads on this, but not sure if these two downstream O2 sensors will work. Amazon lists a different model for right vs left, but I've read on here that they are the same. Anyone know if Amazon is right or wrong? Denso 234-4260 Oxygen Sensor -- Downstream Right Denso 234-4261...

Anybody know of a 10" bolt foot print hawse fair lead with a somewhat narrower (top to bottom) opening than Warn's standard? I have a Warn fair lead with opening a bit under 1" top to bottom but need a bit narrower so the winch rope doesn't drag against the inner bumper opening. If I can't...

Trying to understand some basic DC electrical tech here. Hypothetically, if I'm running with a single battery and it is fully charged and I then directly hook up a second battery (just pos<>pos, neg<>neg) that is fully discharged (to a level that has not damaged the battery) and then drive...

Pease explain me what is the meaning of recurve the dizzy , and why we have to do it after desmog ? What is done to the distributor and why is needed ? In simple , not expert terms , please ..

I'm planning on putting some of these springs on my 97 LX450, which will eventually have a bullbar, winch etc and I was told the springs to get to get a 4"(unladen) lift would be the OME 2850 and 2863. Trouble is, I gave the sales person and old OME part numbers (850J and 863J)and he said that...

'77 FJ40 mustard The EGR cooler has a pretty substantial leak where the cover meets the body of the manifold. Is it possible to replace just the cover or do I need to replace the whole EGR cooler? Searched and found several issues wth 'the big nut' and sheared bolts in removing the...