question

Okay. My dash is cracked like most. 55401-60140-E0 was in stock at first at amayama. However, after paying for it and all it turns out its not in stock anymore... So, after doing some research. 55401-60160-E0 is in stock. From what i can tell, the first one is for 95's and the second one is...

Hey y’all, pulled the trigger on an 07 LC470 with 115k miles on it. Interior is great and engine is perfect, but got some rust to it. Most of it is “surface” rust, but there is some corrosion that has created holes in the rear quarter panels/wheel well area. Has anyone had any luck with body...

After replacing my rear shocks with new iron man fcps my 03 lc is still riding like a safari mobile. Took it to a shop that deals in suspension and they reviewed all my componentry and as I suspected everything is good (not worn or broken). Where he did indicate something less than normal is is...

I was driving home today, while going into a slight curve, my steering got tight and I heard a series of beeps. There are no lights lit up on my dash. Any ideas what this may have been? I just got a new steering rack about a month ago Thanks

I’m putting an electrical component into my 80. For the purposes of my question, it doesn’t really matter what it is. It has a plug, with two spade connectors. (I’m installing an AC compressor modified to be on board air compressor) I have an ohm meter, but not sure I can use it for much, other...

What is this and where does it go under the hood. Pics would be greatly appreciated. The tape marking what it was and where it goes was torn off.

This is how I have my distributor set, I'm afraid that I have it a tooth off on the cam. 83 Fj60 dizzy and flywheel on a 1.5f don't really know if that makes too much of a difference

Same issue that many people have mentioned before, low oil pressure. I have a test gauge connected to the place where the oil pressure sensor goes. It reads 60lbs at start up. When the temp reaches 195ish, at idle, the gauge goes down to 4lbs then after a few minutes, it goes down to 0. I...

So I pulled off my BP51 front struts last night so I can send them in for rebuild and I replaced them temporarily with the OEM struts. In the process I seem to have messed up the caster of the passenger front wheel and now has a rub on the rocker when turning right. I'm not sure which of the...

Good Evening All, Here is the noobie’s 1st question for the brain trust. The attached pics are the current setup on “Wilbur”, my newly acquired ‘73 piggy. Wilbur came from MA and ran consistently between 180 and 190 deg during test drive (it was 68 deg outside at that time). Here in South TX...

As stated, I have a 2003 HZJ78 with tired Dobinsons on a 2" (50mm) lift. I don't know what model or size the Dobinsons are. Looking for some suggestions for replacements options (ideal length, IMS vs remote reservoir, etc.). Maybe new versions of what I have are the best route, if I only knew...

Bought this ‘02 about 3 months ago. The AC will freeze you out, but only blows cold on the lowest setting. If I bump it up at all it will blow warm air. Heat works as it should. Any ideas how to fix this?

I've decided to ditch the spacers the stealership installed when I had my lift installed. Currently running the BBS Forged/TRD Pro wheels (18") and 305/65 BFG's with a SpiderTrax 1.25" spacer. If I wanted to find (or order) a correctly backspaced wheel to get rid of the spacers, what specs am I...

Looking to rebuild my transmission soon. After 350xxx km it feels like it’s getting weak(2nd gear slight flare, 3-2 mis shift, OD manual engagement flare). I’ve upgraded the VB, replaced the solenoids, and TC about 50xxx km ago. Oem frictions from PS are getting harder to get and I’m wondering...

Hey guys I have a really cool vintage North Face tent I got in Japan a few years ago and now have the chance to use. It went together great and looks brand new. Everything was wonderful until I tried to put the rain fly on. It doesn’t look like it fits or matches the tent. I’m posting pics...

I’m trying to solve a “no CEL, cranks, no start“ issue, and while tracking down grounds found two dangling connectors on the wall of the driver’s side panel under the fuse box. The one with the yellow circle is a two-wire connector with black and red wires. The one with the red circle is a 6...

We have a Shasta that we purchased several years ago and I just noticed on our last outing that there are two straps attached to the last hoops on the stationary end. They have two loops sewn in on the non attached side and extend almost across to the othe other side. We don't have a clue what...

Are the manifold studs pressed or screwed in? Whats the best way to get this thing out?

Hello, this is my first post on here, recent purchase of a pure stock 1997 LX450. I am beginning the process of building this truck, one of the things I want to do is run 37" tires and the stock wheels limit choices. I was looking at buying a set of wheels/rims(SCS) and wanted to ask which of...

Hoping someone can help. This carburetor was on my 2F 40. Is it correct because I don’t see a spot to add the stud bolt.