lift

We have found that the rear airbags in the IRS in the 2G Sequoia work amazingly well in this platform. They offer a ton of advantages with very little downsides. They allow the truck to self level and adapt to whatever weight its carrying and they don't bind like the springs do during...

Looking for 4" and 6" 80 series rear springs to mock up under my 100 series... don't ask If you have a set laying around I'd like to potentially purchase or borrow if that's feasable

I want to do a 1.75” Dobinson lift on my ‘16 Sequoia. I’m having trouble trying to figure out the right size BF Goodrich KM2 to use with my stock 18” wheels. Is the 34 x 12.50 the best option? Thanks for your help

I have a lifted 07 limited sequoia and need to replace my inner cv boots. I was going to go with a high angle cv boot but wanted to see if anyone could reccommend a brand or is it best to stick with oem? Thx.

Question for anyone running a Lx570 with sensor lift for 2 or more years. Any noticeable long term effects? My hunch is that the sensor lift puts extra demand on the hydraulics and can cause premature replacing at a minimum.. input/feedback appreciated

Icon 2.5 lift kit Air bag deletes Snorkel upgrade RCI Rear differential, transfer case, lower link armor SBW air system linked with ARB dual air compressor (air up/down all 4 tires at the same time) 17” Volk Te37’s (5) brand new spare (full size) BFG 285/75’s KC Hilites Chase and Rock lights...

I plan to install a set of BFG K02s in the near future and I know the tires will be larger than the military set my BJ40 is currently sporting. I'd like to buy a Hi-Lift jack but I wanted to mount it inside the 40, under the jump seat. The only size jack that will fit is a 36" . The 48" is too...

The tires are 11 years old and suspension 18 years old. I'm FINALLY ready to pull the trigger and change out the suspension. I installed it myself but will be using a shop this time. Current OME kit said 2-1/2" lift and had the castor corrective bushings. A few years later I upgraded to 10.5 x...

I thought you needed kdss spacers to lift more than 2 inches? Maybe a link to those or anything else that may need a tweak as far as proper procedure.

99 - 02 100 series lift gate

Just ordered a Medium Duty 2" lift for our 71 fj40 and was wondering if anyone on here is running the same lift? I searched for pics/threads on Ironman Fj40 lift here on MUD and could not get much info. Any thoughts vs OMEs or Dobinsons'?

Purchased this a little over 3 years ago. Has approximately 27,000 miles. Still felt great when installed. No issues. Just your typical road wear on the rear shock body. I just recently upgraded my suspension. 4 Used Standard Length Shocks 2 Used 850 Springs 2 Used 863 Springs 1 Used Steering...

Summit has some ARB "protection steps" but they're only good for up to a 50mm (2") lift per the installation instructions. Looking for a bar with steps that's not too busy. Prefer black and not crazy money. Thoughts and pics welcome...thanks in advance! HS

Hi All Recently welcomed the below 2006 VX into the family. Only owned for about 5 months so still learning her but noteworthy mods include 3" lift (with diff drop) which i have since corrected as torsion bars were wound right up, suspected high flow cats and exhaust. Baselined all fluids and...

I could use some of your expertise and guidance please about the rear coils of an 03 limited sequoia 4wd. I installed 1.5” rear spacers in conjunction with bilstein 5100s. I have confirmed that the shocks are not limiting travel bc as I jack up the frame, there is room for the shocks to travel...

Hey all When you are looking at lifts from different companies, is the lift height difference measured from normal AHC, or high AHC mode?

Hi all, First off, I did search but didn’t find anything. So apologies if this has been discussed before. If you have 33’s and a 2” lift, what’s your overall height of your 40? My garage is 84” and I want to make sure I’ll still be able to get in my garage after installing my tires and lift.

I'm planning on putting FCP suspension on my 2017. I only want to lift it about an inch. I can use some Dobinson rear springs for 1" in the rear and wind the preload adjusters down on the front. My question is about the panhard bar ("stage 2"). I don't think I'll need the adjustability...

Installing 2.5” lift. Loosened kdss valves 3 rotation and LC is on 4 jackstands. Rear install of shocks/coils/airbags went fine. Using OTRAMM video as my guide but encountering problem up front getting ball joint loose from upper spindle. (Circled in red blow). Nut came off fine but not able to...

Went on after installing the lift. Can’t read on scanner. What’s the possible things to check?