lift

Hi All Recently welcomed the below 2006 VX into the family. Only owned for about 5 months so still learning her but noteworthy mods include 3" lift (with diff drop) which i have since corrected as torsion bars were wound right up, suspected high flow cats and exhaust. Baselined all fluids and...

I could use some of your expertise and guidance please about the rear coils of an 03 limited sequoia 4wd. I installed 1.5” rear spacers in conjunction with bilstein 5100s. I have confirmed that the shocks are not limiting travel bc as I jack up the frame, there is room for the shocks to travel...

Hey all When you are looking at lifts from different companies, is the lift height difference measured from normal AHC, or high AHC mode?

Hi all, First off, I did search but didn’t find anything. So apologies if this has been discussed before. If you have 33’s and a 2” lift, what’s your overall height of your 40? My garage is 84” and I want to make sure I’ll still be able to get in my garage after installing my tires and lift.

I'm planning on putting FCP suspension on my 2017. I only want to lift it about an inch. I can use some Dobinson rear springs for 1" in the rear and wind the preload adjusters down on the front. My question is about the panhard bar ("stage 2"). I don't think I'll need the adjustability...

Installing 2.5” lift. Loosened kdss valves 3 rotation and LC is on 4 jackstands. Rear install of shocks/coils/airbags went fine. Using OTRAMM video as my guide but encountering problem up front getting ball joint loose from upper spindle. (Circled in red blow). Nut came off fine but not able to...

Went on after installing the lift. Can’t read on scanner. What’s the possible things to check?

I know this is not ideal but I'm looking for a mild lift for the rear with a 1.5" ebay spacer. Unless anyone on here has some for sale or 1.5" lift springs. Any thoughts are appreciated. Thank you. I'm doing 5100s on the front and rear and will do a .75" front lift and 1.5" rear lift.

Been hemorrhaging money on this old Landcruiser lately, what's a little more? Vehicle is a 1995 80 series with ~350k miles. Currently has ARB front bumper, ComeUp 9.5 winch, and MetalTech sliders. Rear bumper is stock, no cargo drawers or anything at the moment. As for me, I've been building...

I’m getting ready to pull the trigger on an OME 2” lift for my 85 FJ60 that will be running with 33x10.5 on stock 15s. The cost is $2k+. Any solid alternatives out there that cost less or is OME worth the $2k?

I'm looking at a 200 with an aftermarket lift. I know it's pretty common, just wondering if there is anything that can be done incorrectly that I should be looking at. How difficult/expensive is it to return to stock height? This is the truck. It is going to be a DD so I will probably have to...

Putting BFG 33x10.5 on my 1985 60. Will a 2” Old Man Emu be enough or should I go 3”?

I purchased a parts 40 a while back, and it had these, what appear to be, lift springs in the back. They look pretty much brand new, so I would like to use them, if they are descent springs, and in the 2.5" range. I searched the part # and it looks like they may be pro comps, but the yellow...

Gone please delete

So I’ve had this 1986 FJ60 for eight years. The previous owner did an SOA lift. No cut and turn on the knuckles so she’s all over the road. I want to drop it back down and have a bit of lift yet turn it back into a good driver. The original spring perches are still there so I figure I’ll drop...

Need some help figuring out what to do next. FJ40 with 11/78 build date. Installing a Dobinsons full IMS kit. Passenger rear went together great. Driver side rear is presenting a challenge. The spring hanger pin flange screw holes do not line up with hanger bracket. I tried the 3...

Hey guys tried searching for something similar to my situation but couldnt find exactly what i was looking for so i gathered a new things from different threads. Planning to go OME 3 inch lift and have everything in my basket but having some last min decisions. I am looking for a firm ride...

Hello everyone, this is my first post sorry if its lacking info but i just picked up a 470 and looking for recommendations for a 3 inch lift that wont break the bank as this would just be an entry level setup. I came across OME being one of the more “reliable” options but im not sure how much of...

https://quinnsauction.appspot.com/auctions/KPzWaQ2Cjuvts2dZ1deR

After installing the 12.5 LRA tank, I was hitting the bump stops way more often than I wanted. No other weight added to the truck. And that's driving the streets of Memphis. Bought a 2" Ironman FCP kit with the softest springs. (0-440 extra pounds) Just springs and shocks, no UCAs as they...