lift

I have my drive train and block assembled but once the transmission and transfer case are not supported by the transmission jack it rolls and not sure how far it will go. Even when just lifting the gear boxes with the transmission jack I need to use the floor jack under the output side of...

Here we go, I am trying to determine what lift is needed to clear 35 inch tires on a FZJ80 ? 2inch Dobinson Claims or more? Like maybe 4 inch? Been advised 4 inch have to redo my from drive shaft, then castor corrections would need to be made. Then Ofcorse bump stops, brake lines, sway bars...

I just did a lift and got new tires. My TPMS was having intermittent issues reading the spare about 6 months ago and then went to consistently just showing a fault. I asked the tire shop to check the TPMS and likely replace the one in the spare. They did and said the old one was loose inside...

I have a 2007 non kdss with 118k miles. Toyota suspects that I may need new UCAs and could have a potentially bent front left suspension causing a really bad camber in the front left wheel. Im wanting to do the OME 3inch lift kit with their UCAs and rear coil conversion kit. Im also going to...

Been going back n forth on wether 2"or 3" caster correction arms would be better for me. I don't have current actual caster numbers. I'm just estimating based on the info I've seen out there..~1.7 degrees per inch of lift. Looking for your feedback on both if you're using one or the other...

Somehow I managed to find and import a single owner 97 Hilux with 44,000KM and zero rust or mechanical issues. It even came with the service history every year it went in. It’s a LN-165 with a 2LTE. I’ll be blocking the EGR off, swapping thermostats, possibly adjust boost and putting a straight...

I would like to put 35” tires on my 2000 LX 470. How much of a lift should I be looking at? What kind of suspension should I replace the stock suspension with? I’m really reluctant about replacing the stock suspension and would only be willing to replace for a smoother or equivalent...

I'm digging around in the electronic parts catalog (EPC) and don't see a lift pump in the tank, on the injection pump or elsewhere. Has anyone done a fuel delivery/supply write-up? I can see all the parts in the EPC, but it would be nice to understand the basic fuel delivery. It's 18°F outside...

Installed ironman foam cell pro 2in lift with dif drop kit. I made the mistake of choosing the heavy rear springs rated for 440+ and the rear came up almost a full 4 inches, was hoping it would be a little more firm but sit at just the 2in lift and be able to float a motorcycle off the back...

Just installed ironman FCP on my son's 2014 Luxury. Removed the airbags and put the washers under the bracket for the headlight leveling and I am still getting both Check Headlight System and Check BSM System. Is there something else I am missing? I have searched and searched and cant figure...

i've been talking back and forth with accutune about a lift kit. apparently my truck weighs a lot more than i thought it did. they are recommending the 14" 700 lbs king coil over in front and the icon-52800 3" spring for the rear. granted i'm a bit of an idiot when it comes to suspension tech...

Would you do a 2” lift and bigger tires if it’s your daily or keep it stock? I do not think the stock ride is all that comfortable, so many a mild lift would help? If so, which lift would you go?

Hi all, Maybe I'm jumping the gun before getting an alignment, so let me know if you think that's the case. I recently had a Dobinsons IMS lift kit delivered and after installing it, the lift was about 3.25 inches in the front and I was expecting ~2 inches in order to level it with the factory...

Just placed an order for custom 5 inch lift springs from Alcan spring. Going from a Rancho 2.5 inch lift that sucks I’m excited to feel the difference in ride quality and flex! Will the Bilstein shocks designed for a 4 inch lift kit work with a 5 inch lift kit or do I need longer shocks? I...

Anyone running the freedom offroad 2.5-5" lift kit? Their upper control arms seem pretty good quality I'm wondering if the lift kits are any good.

SOLD: Old Man Emu 2” FJ40 light/med lift leaf springs, shackles and u bolts. Approx 1500 miles of on road use. For 58-74 with 25mm eyelet holes. I finally installed my Dobinsons. CS001F x2 springs front CS001R x2 springs rear OMEGP8 x4 greasable pins OME59a x7 u-bolts OME59b x 1 u-bolt FK08...

Hey! I'm looking to replace my OEM Torsion Bars, Rear Springs, and all four Shocks. My OEM torsion bars are so worn out that I'm sitting at stock height with them crank all the way down (up), and I don't want more than 1.5"-2" of lift in the front, and potentially 1"-1.5" in the rear. I was...

Hello, I have a question with regard to the potential driveshaft modification after a 4" lift on a BJ 41. Is it required to modify the front and/or rear driveshaft(s) after installation of a 4" lift (without front shackle reversal) and installation of longer front and rear shackles? If yes is...

2" Ironman lift w/extended cap rear spring w/spc control arms RLC rear bumper Prinsu roof rack Redarc brake controller Cell booster HAM radio setup 5 TRD Wheels Asking $35,500 obo

Hello, I have a tried the AHC sensor lift method, and followed the videos and write ups on here. I did not gain any lift. My truck AHC system works with no issues. Just need help or advise with the AHC sensor lift please. Please advise. Thanks