install

Hello all. I am about to tackle the task of replacing the weatherstripping for all 4 sliding side/rear quarter windows on the troopy. Just wanted to see if anyone has any pointers before I get started? I am going to (would like to at least) do it without removing the whole window frame so I...

So I got my new UCA's in and am trying to understand how to get the top of the knuckle/upper ball joint away from the brake line and shock. I have the caster on setting D which they it says is good for 2-3 inch loft I don't understand the whole camber/caster settings. My plan was to get this...

Hi all - don't post much, but looking for some advice. Currently in the Dominican Republic and returning to the US soon (San Diego area). Shipping LX back in May. Currently she is at 125k so I just did a bunch of preventative maintenance - changing all fluids, lube, repacking front wheel...

I'd like to put some additional exterior lighting on this thing. I'd prefer to use whatever existing wiring harness provisions exist, whatever slot exists in the fuse panel, and a factory switch put into a blank on my dash. Where do I start digging?

Hi, I thought I would put this out there to see if there is a fellow 120'er who would be able to help me install my IronMan lift. I just moved so we could use my garage I also have all the proper tools or I could meet at your place. I am in Vancouver BC but I also am back and forth to...

HI all. I've done enough reading to have a fairly good understanding of how I can rig up a 24volt to 12 volt reducer in my 1990 70 series 1 PZ system... though through all my searching I can't solve one final dilemma. My reducer has 1 each of 24+ and 24- wires. I plan to ground the negative to...

Hey folks. So, I have everything else done, new tranny, desmog, headers, exhaust, Weber carb, and everything. The last thing is to get this dizzy installed and I can start her up! The problem is I've spent all day and last night trying to get the damn thing to seat to no avail. I've done...

Hey guys. So somehow my rack does not line up with my mounting points. Am I missing something? I can't scoot the rack back because I'm as far forward as possible on the rear and the front mount sits on the cross bar not on the mounting plate. See pics. Anyone have any ideas on how to get...

Been doing some soul searching after regaining possession of my 95 FZJ. My girl was taken by flatbed to a local dealer with highly skill LC wrench. Upon inspection, as feared, the engine needs replaced (the previous short term owner ran the poor girl with absolutely no oil). The service...

I'm going to be doing a full hose /coolant swap on my engine this weekend and I'll be adding a "T" fitting for the temp gauge. I'm thinking of putting it down below the ash tray or on the left side of the cluster.

I need to buy a rivet nut installation tool. Wish list: -- Capable of at least 1/4". -- Fairly durable -- Price $75 max Question: Are the blank rivet nut slugs standard or do you have to buy Brand X nuts to use with a Brand X install tool? Ran across the Astro Pneumatic Tool Co model...

Ok I ordered these before christmas and have just been busy building motorcycles with my 13yo son I'd rate the seats/leather a good 8 out of 10, there are several threads on the install so I won't rehash whats out there... you do need to steam the foam while the old leather is off ... my foam...

Took me months to get back to putting the carb back in. Dont recall where this bracket goes? Any help is much appreciated.

Installing new ARB front bumper on FJ62. The ARB brackets fit my frame, but the leaf spring mount covers the rear mounting hole. It looks like the PO may have altered the front leaf spring mounts. The mounts are to far forward. Thoughts on a work around?

I purchased the seatbeltplanet.com FJ60 rear retracting seat belt set to upgrade my 1987 FJ60 rear belts. The old lap retractors were old and jammed, and I want to be able to take along the whole fam on trips. Currently only 2 can ride with me, and one has to "ride bitch" using the rear center...

I'm having some alignment issues following my OME install. The truck still pulls to the right even after an alignment. It's not terrible but it's definitely noticeable at highway speeds. If I take my hands off the wheel, I'll be in the next lane within a second or two. I took it back to the shop...

I've been slowly rebuilding my front end drive train since last August when I had an unfortunate incident on a gravel road. I won't go into that in detail here, but one of the results was a blown front differential. A few months ago I was made aware of Harrop's option for the FJC through...

Does anyone know a reputable person around Houston, TX who could install power steering in my 83" BJ42? Thanks

Pretty new to posting on here so please forgive my forum etiquette. I have a 96' LX450 and was searching CL when I came across an OEM center console refrigerator from a Japanese HDJ80, the price was right so I picked it up today. I have searched the forums, and could not find a lot of...

So I picked up a used ARB locker, I believe the model is an RD08. It is an older unit and uses a 1/8 BSPT bulkhead. I'm having trouble finding parts to connect the 3.5 mm line from the compressor to the locker. anybody have any recommendations? I called ARB and looked through their parts...