ignition

Hi fellow TLC lovers. My key has worn out the jgnition switch. Is it expensive to replace and can it be done without special tpols?

I am looking for an original ignition switch with a key for a 63 fj40 fj45. It has the 4 posts on the back with a screw in each post to secure the wiring connections. It may be the same ignition for other years but I know for sure it changed in the 1970 models.

So I was out washing the cruiser today and backed it out of the driveway to play vehicle dominoes so I could get it in the garage and out of the sun. Got back in it and started it up and was greeted with a loud buzzing noise coming out of the dash/steering column area that I have never heard...

Bought a 2000 LC in March of 2016. Had 120k on her. Since then I have gone through many repairs; both exhaust manifolds, catalytic converter replacements (In California its very expensive), new brake rotors and twice have had my ignition coils replaced. The truck has about 140k on her now. Check...

So i've had a couple threads crying about my weird electrical issues after a stupid driving decision on my part. We traced back to the ignition coil today and I think it may be the problem. My rig will turn over, but not start. 1. Both wires coming out the coil seemed to have current with...

I posted before when this happened to me a couple months ago how by following the simple instruction on this forum to remove the ignition lock cylinder and the broken rod ... you can start the truck using a 7 or 8 mm socket or a 3/32,,,,, 1/4 drive socket on a 6-7" extension or nut driver...

I'm almost done with an ARB compressor install and the last step is to wire the dash switch to ignition and illumination power. How do folks typically do this? I'm installing the switch in one of the open spots in the driver side kick panel. I tried searching but surprisingly didn't find a...

Hey guys, looking for any insight on wiring an ez wire harness to my existing steering column. I have listed what I have below currently. I'm not much of a wiring guru but have made it to this point and I'm eager to get the rig fired up and not ON FIRE. EZ wire -ignition switch start...

Is there anything available? Is it worth the trouble?

Just found this rummaging through my parts. Shipping on your dime from 20912.

I have a '99 with 185k miles, and turning the ignition at times does not start, engine doesn't turn over. Very intermittent and no specific pattern. New battery, no difference. Dealer checked wires and connections and starter seem ok. Could it be the ignition switch? Turning the key to...

You pay the cost of a medium flat rate box. For early distributors, two wheels and eyes, one ignition thingy. Great spares if you run this setup. No idea what works, off various parts rigs. No, the distributor is not included, currently getting a Pertronix.

Currently my key is stuck in the ignition because it will not turn CCW to the "Lock" position. This started happening intermittently a few days ago. Occasionally when I went to turn the vehicle off the key would not turn back to "lock" and release the key. After sitting in the ACC position...

Hey y'all, I could use a little help with the wiring involved with starting my '72. I tried searching but can't seem to really find what I need, so I'll just have to ask. Several weeks back, the original starter crapped out on me. Everywhere I looked seemed to recommend switching in a GR from a...

Hey guys, My 89 62 has been running great but all of a sudden two days ago the engine cut out as I was driving home from work. Then when I tried to start it again it would start and then immediately cut out. Turns out the the shut down VSV was not working properly or so it seemed, as it was...

Hi all, First off, let me just say thanks for the community here. I just picked my my first Land Cruiser (1988 FJ62), and the forums here have been great place to read, learn, and even helped solved some of my problems so far (locating and verifying engine timing!). But I'm posting today...

Ok ok i don't know much about electrical systems. Cruiser was running fine. Then turned it off. Turn the key to start it...nothing. no power at all. No gauges, no lights, it's as if the key wasn't even in the ignition. 2 hours later try again. Turn key cranks right up. It starts...

So I picked up the piggie in Ft. Collins last week, the white one that belonged to TJ's old neighbor. Crusty, but runs and drives nicely,and the interior is very nice. I promise to start a build thread soon! Anyway. The battery was dead, so a few days ago I jumped it, and let it run to try and...

Just an update on what works for more than a few weeks.. Denso 673-1303 YEC Flamma IGC107F Toyota 90919-02230 Toyota part number is at the best price point on the nefarious auction site right now: 50% of Denso (under $30), if you buy a new part from the bulk packagers. I have installed all...

So.......... started right , up idled fine , went bout 30 ft and just died . getting fuel , no spark , threw a new coil in cause it was cheap , close to work , so figured i'd try quick fix...nothing not even a fart......so i've pounded the threads and pretty much have a plan on checking the rest...