head

I have a few things that I ended up not needing for my engine rebuild. These are brand new, OEM parts. Might trade for ARP head bolts or cometic gasket. Head Gasket- $75 (SOLD) Oil Cap- $10 Head Bolt Set (Qty 14)- $175 Parts are in OKC, OK.

I have a freshly rebuilt 2F Head for sale that is ready to go for someone's domed piston 2F build. All work on the rebuild was done by Kennedy Performance here in Lexington, KY. (I can furnish the receipt verifying the work done to the buyer or prospective buyers). The following list was...

Hi everyone, This is my first post here on IH8MUD. I have been successfully wrenching (thanks to forums like these) on a few Toyotas ( 95 T100 5vz-fe w/ 459km on it, and more recently a 85 Hiace Pickup 2L with 92km) now for a while. I find much of the information here useful and I am hoping to...

Hi all. As part of my 2lte upgrades roject I'm researching head replacement options.. I know a 3l head will fit but I'm intrigued with a 1KZTE short valve head.. it's the bigger intake & exhaust valves.. So will this head fit my 2lte block?? Thanks for your replies in advance..

I bought a well maintained ‘97 LX450 from a neighbor a few weeks ago. It has 188K miles, just had an oil change and it was running like a top before I took it to a local Midas yesterday for new belts (a/c, alternator and v-belt). Midas also replaced the fluid in both differentials and my...

I've been looking into this a bit because I got an incorrect (ports too big) fuel primer head a while back and didn't realise until then there were two sizes of fuel line fitted to 80's for the Australian market. So I went looking in toyodiy at the p/n's and discovered that for mine (1992) the...

I need help identifying compatadability with my block and head. my block vin is 232080 and I have attached some pictures of the head. I'm trying to change the head gasket but can't figure out what gasket to get and if the head I'm using will work. I think the block is an early model f engine I'm...

7/'79 FJ40 So you may have seen other threads where I was asking about ignition and emissions issues. Here's a head issue. One of the main reasons I started to work on the vehicle was I was getting significant oil/gas in my carb (Weber 2 Barrel) to the point it was smoking. Figured we'd...

Guys, I bought another head for my 88 fj62 and don't need it. It came from a running engine with good compression. I took it to the machine shop I always used and had them recondition it. It has new valves, new springs, and new seals. It has been pressure tested and magnafluxed. It is...

SoCal from an FJ80 1991 3FE engine block without head Exhaust System - Complete or Parts Coil Sensors ECU Alternator (not the big one) Starter All Brackets PS pump (pulley has been sold) Air Conditioning System or parts, compressore, lines, etc (R12 system) Radiator Water Pump ETC...

I'm planning to rebuild my head in the next few months and I want to read up as much as possible. I can't find anything in the FAQ section for the 60's or 40's that seems to be the definitive guide to rebuilding the head. Other than the FSM can you point me in the direction of any threads that...

OK guys, let me try to do the best explanation i can on this. I have an 88 fj62 with the 3fe in it. Bought the truck 4 years ago and the motor was toasted. I pulled it and did a full rebuild, slapped it back in and drove the bejesus out of it for the last 4 years as a daily. The engine had...

I have done some searches and found info pertaining to the freeze plugs on the block and while the engine or head is out. I'm wondering if anyone has successfully replaced the freeze plug on the back of the cylinder head while still on the vehicle? The space seems pretty tight and I'm wondering...

Hi guys, i am new here but i was told you are good for technical information. I have just performed my first ever cylinder head swap, and i followed all the instructions and i think i either messed up or i got a crap head. The head is a "new" one from the wreckers, it was straight to my...

SoCal Hot tanked, inspected, Valve Job and Resurfaced, Cleaned ports, Nice Work, Receipts. $675 firm. Shipping available - Crate cost $70 + actual cost to ship. Fits 93-97 and some 98s. Send Personal Message for more info.

like the title says i have a good block and head from an 84 2.4 diesel located in Reno NV text is best 801-564-9029 Ryan $100 each

It seams the PO was a douchebag. let me rephrase he really was When somthing broke that is not critical he would bypass it When I got my Rig I filled the washer tank with good blue stuff every button i pushed I got water on the front window I read here and searched here all the posts...

I installed a new head unit. Worked perfect for a month then all of sudden i get no sound at all. I returned the head unit and installed the new one and the same thing. I bypassed the factory amp. When i remove the rear speaker harness only the front speakers work.

Tall driver here, looking at picking up a GX470. Being 6'9", fitting in a vehicle is always a concern. I have a pair of 80's, one with custom seat brackets that I built to make things comfy, so some one-off fabwork is ok with me. So, any tall drivers out there in a GX? How big are you? How...

2001 LX470 I have power unit turns on but no sound. My wiring harness has ground wires for the speakers but the vehicle harness has no speaker grounds. Im using the diagram below. Where do i ground the speakers. I do have mark levinson i can turn the am on and off in the head unit. What do i...