head

While doing a valve adjustment for a customer, on a 91 FJ80, I noticed a glimmer of green in the sun. After pressure testing and cleaning the suspected areas I found this. It is located between the exhaust valves for cylinder 2 and 3. There is also a smaller one in the same spot but between...

So we are making good progress getting the interior stripped to clean up all the mold we had in our 93. We picked up a complete interior (carpet and seats) from another forum member from a 94 and have thrown away all the other mold ridden seats and carpet. I did remove all parts from the seats...

Looking for a 2F Cylinder Head for an 84' FJ60. Please message me if you have one available.

Hello all, I had my '11 LC undercoated with Krown undercoating yesterday. I didn't notice this issue until today, but the little black tabs on the front bumper that raise up and wash my head lamps are not working and are stuck in the up position. When I press on one end, the other end goes up...

I am about to put the cylinder head back on after a headgasket replacement. Bolt holes look clean and thread in without a lot of friction. I plan to use new OEM head bolts oiled per FSM. Reading on mud some say to chase the threads. FSM does not state to do this. I plan to run my bolts down each...

Evening everyone, Cross posted here to hopefully locate something. In need of a 3b cylinder head shipped to 93442 morro bay California. Or I can arrange pickup pretty much anywhere in California. Thanks everyone Cheers, -Joe Rawson JoeRawsonSLO@Comcast.Net Wanted - 3b cylinder head

In need of a 3b cylinder head shipped to 93442 morro bay California. Or I can arrange pickup pretty much anywhere in California. Thanks everyone Cheers

Evening everyone, I recently came across a FJ60 with a 3B and H55F swapped into it. Motor wouldn't start and had very poor compression. After pulling off the head it appears to be cracked pretty badly. From my understanding all the pre cups are cracked along with that all 4 chambers have cracks...

Ok, I lied.... It is another 1FZFE head gasket thread. Backstory: Had heat, lost heat, filled rad, had heat, lost heat, checked rad, low coolant, filled rad, changed rad cap, saw white smoke, parked truck and started ordering parts. Please note that I am by no means a pro, and this is my first...

I have a 78 FJ40 that has dome pistons. I am looking for a cylinder head. The one that I had on it was open chambered. Thank You, Rob

I need a head for a 3F engine. Would love to know if anyone has one state side.

Good Morning everyone Here's a picture of my 1F engine that I been working for a few months. Between waiting for the parts to arrive from the USA and finding parts here in Ecuador it's taking a long time to finish this project. However I'm having fun and I'm learning so much. I'm ready to put...

My Son and I finally got to take the cruiser on her maiden voyage tonight.. After a few months of working on it and fixing all the things that go bad when a vehicle sits for a few years.. Anyhow we took it out at night to the car wash and noticed when you turn on the lights you get a very...

Hello all, I have a 95 with 150k - runs well - good compression and yet I have that lovely chocolate milk frapuccino crud in my radiator and overflow. I took apart and checked the oil cooler - redid seal and pressure tested. All good. Still oil in coolant. Then got the head gasket and all that...

Well I've been offered a 96 ute with the 4.2 in it. With a blown head is it a diy job or approx how many hrs would a shop charge to do it. Is there anything else I should look at at on the 4.2 while I'm at it.

Hi, I have a slight problem with sleeves / tubes in my 12HT cylinder head. The engine rebuilder who pressure tested the head before skimming just said - there´s is a leakage into some of the head bolt bores... An good hour of searching the web had given me just one goal... this meber has had...

good morning all, I'm new to the forum and new to TLC's. I spent the last year and some trying to hunt down a mystical unicorn (diesel gwagon long wheelbase from the early 90's). A good friend sent me a few reviews to the TLC's and I dropped the gwagon flat on its rear. That being said I'm a...

Any of you know of a way to upgrade the headunit? I'd love to get a double-din in there but I think the fact that the climate controls are on the headunit will be a problem. Any suggestions? I LOVE this car, will drive it forever, BUT only if I can upgrade the headunit, which is worst GUI ever...

I was planning on doing my headgasket so I picked up a head from another member here and had a good machine shop rebuild the whole thing, I got all parts and seals from onur, head gasket every thing but unfortunately I won't be able to do this project for awhile nd I could use the cash. I...

I was planning on doing my headgasket so I picked up a head from another member here and had a good machine shop rebuild the whole thing, I got all parts and seals from onur, head gasket every thing but unfortunately I won't be able to do this project for awhile nd I could use the cash. I...