gasket

We've owned our new to us 91 FJ80 land cruiser for little a year. The vehicle has done us well and we use it as back up vehicle. The wife drove it about a week ago and said the engine got a little warm while picking up kids from school. I go start it and it's now a steam generator:censor...

SoCal AVAILABLE AS OF 7/8/17 Gasket $50 firm + shipping at actual cost from 91780. Toyota Part # 56121-60100 fits all FJ80s without chrome windshield trim. Windshield $50 firm NO SHIPPING. Paypal OK. The rubber gasket is not for chrome moldings. The rubber is soft and pliable, no cuts or...

1994 Fzj80 with 277k miles recently blew a head gasket due to a upper hose that split open while on the road. The owner is my neighbor and he just wants to get rid of it. Body and interior is in decent shape with 3rd row seat but no lockers. It is still running but steam starts to come out of...

The molding on my windshield doesn't seem to be seated very well and I'd really like to take a look underneath it to evaluate but I'm not sure if that's a good idea. I can see a lot of sealant from the previous install, and I'm getting water in the cabin (of course right after replacing the...

Hi All I need to make a few gaskets to seal the sender and inspection plate. it's a galvanised aftermarket fuel tank and the surface where the sender fits is a bit warped, so i need a thick soft gasket here, What is the correct material to ask for please. It need not be bio diesel compatable...

So I need to replace my 97's oil pan gasket and I'm a bit confused on the part number. It appears to be 12151-61011, but that part seems to be from 91 to 93. Can anyone confirm? Thanks, Dan

Ok, I lied.... It is another 1FZFE head gasket thread. Backstory: Had heat, lost heat, filled rad, had heat, lost heat, checked rad, low coolant, filled rad, changed rad cap, saw white smoke, parked truck and started ordering parts. Please note that I am by no means a pro, and this is my first...

Wondering if it's common practice to use a new oil plug gasket every oil change? (FJ40) I don't on any of my other vehicles but now my 40 is marking his territory again and is subject to banishment by the queen!

I am currently doing my no. 1 oil pan FIPG gasket on my 1993 FJ80 with the 1FZFE. Does anyone know the name of or where i can find the gasket that goes between the no. 1 pan and the oil pump. in the diagram it is #4.

Several of you guys have helped me with my timing cover gasket and front crank seal. Got the crank pulley back from sand blast today and getting ready to put it all back. As you know the gasket for timing cover is a vertical gasket. To help hold it in place was thinking of small bead of permatex...

I have a used 81-84 windshield gasket (may fit other years not sure). 25$ plus shipping 801-209-7396

I have just removed my flares for a coat of Duplicolor. My truck is two toned Green with the silver trim. That includes a silver stripe base on the doors. I was going to paint that too with the Duplicolor but I started to think of what the new gasket material might do to the semi-removable...

I have a 2f in a 1978 fj40 that was rebuilt by PO in 2012. The engine may have 100 miles on it. Now the oil is getting water in it. I am thinking pulling the head and redoing the head gasket and then go from there. What would you guys recommend? Thank You

I just bough a 1997 Land Cruiser with 140k miles. The head gasket blew 2.5 years ago and has been sitting ever since. I drained the oil the other day and the oil wasn't all that brown and milkshakey, however there was coolant in the oil. I got about 12 quarts of oil/coolant out when I pulled the...

Hi, Do I need to remove my injector lines to replace the manifold gaskets? If so, will the engine restart by using lift pump or will I need to have an injector pipe open? Dave

I just got a Overhaul Gasket Kit from CC. However they don't identified any parts on the kit. My cousin is sending the manual from the USA and it will be here with in the month. Can someone help me identified these items Thanks Bill D

I just bought a 2001 LC with 201k miles that has a blown head gasket. I have replaced a few head gaskets before on various makes and models of cars so I was not too scared of buying something that needed some serious work. That and the vast knowledge of members and good threads on this site...

Wondering if anyone has ever found a solution for a problem I am having. I have the standard 3 bolt flange gasket connector under the drivers side of my custom build exhaust. Fel-Pro Collector Gaskets | JEGS I have used copper, aluminum, compressible, etc gaskets and have used standard and...

All parts are brand new. Prices are what I paid from Beno. Sold the 40, so I don't need these. Clutch Slave Cylinder for a 2F/4Speed. 31470-60071 $72 + shipping Oil Pan Gasket for a 2F. 12151-61010 $25 + shipping OEM Rear Main Seal for a 2F. 90311-99065 $55 + shipping Shipping...

New member and first post - if I do something wrong let me know! Torrential rain in NCAL surfaced a rear third brake light leak in my new to me 2006 LX470. Thanks to many many entries across this site for trouble shooting help - found it with foam and then saw it dripping inside the back...