exhaust

Just a ton (ouch) of china companies putting these out now. But i like the roll up traction aids at these guys site, and they have snorkle kits for all cruisers after 80's. China Snorkel manufacturer, Wheel Spacer, Air Jack supplier - Telawei 4x4 Off-Road Accessories Factory Telawei 4x4...

Took my 1hz's old Genie headers off yesterday - they have a fair number of weld cracks and pinholes due to rust/age/vibration/etc. all of which couldn't be seen without removing them. To be honest, they are pretty ugly and one of the weld cracks was 1/2 way around at a join where three cylinder...

Anyone have the FJ62 exhaust center pipe (between the cats and muffler) from an FJ62 laying around that's in decent shape? See pic.

Hi, '74 FJ40 with original F155. I just noticed a fluid leak from or near one of the bolts connecting the intake and exhaust manifolds together. The obvious thought is gasoline, which it smells like gasoline, but it doesn't evaporate like gasoline should (no, i haven't put a match to it)...

So Cal Nice clean one that goes behind cat to bring the twin cats into one pipe. $40 + shipping. Paypal OK

[No Longer Available] The guys at ACC Garage are working on new header-to-resonator replacement exhaust kit. Here are some teaser pics of the first install. I neglected to get a pic of the muffler, but it is nicely sized and surprisingly quiet. What I know about it at the moment: Maintains...

SoCal. Prices from $25 per item to $100. Shipping is available, but can be costly. However total cost will still be much less than new. From a Local car with no rust issues - Exhaust Manifolds Heat Shields Headpipes Y pipe Dual Cats Cat Heat shield 02 sensors Resonator etc. Send message...

Does anyone have the following "J" pipe nut shown in the picture below?

Hi, I was looking for some part numbers related to my Driver Side exhaust manifold replacement on a 2000 Land Cruiser. It was lots of fun to take off, but i'll save that for another thread. 1) here are 8 nuts that hold the exhaust manifold to the engine. I'm not replacing the bolts because...

I have two exhaust leaks, including one at one of my down pipes. The exhaust was new about 4 years ago but RJ's Muffler on Capital Blvd. I have had to return every year since to fix little things. They have covered all at little to no cost, but I'm getting tired of returning every year...

First off, this is my first post but ‘Mud has been a massive resource for me these last few months. In the last year I acquired a 92 FJ80 and since I’ve slowly been building him (“Lando”) up. So far: water pump, belts, hoses, power steering pump/pulley, PCV/grommet, tires/wheels (Duratrac...

Forced Air Technologies Review “FAT” mistreated my vehicle & left paid work unfinished I have never written a negative review before but I feel that Forced Air Technologies and its owner Robert Ansick have mistreated my vehicle and their customer so egregiously that they warranted this review...

If any of you have some old California legal Downey headers laying around or know someone else who does, and wouldn't mind making a few extra bucks, I'm in the market. And by that I mean I really need some, since apparently a machine shop can't resurface exhaust headers because of the no. 1 and...

2f bolts?? by Rkbaseball posted Jul 27, 2017 at 10:00 PM Does anyone know what the bolts on the heads above the exhaust manifold are for? There is one bolt for each cylinder and they are directly above each exhaust port. They are circled in red Thanks!!

Looking for a 75-78 FJ40 Exhaust Downpipe or at least the flange connector at manifold. Let me know if anyone has one. Shipped or local pickup to 18901.

I am looking for a smog legal header for a 1977 FJ40. Jeff

Brand New Magnaflow Catalytic converver for FZJ80/LX450.I can't tell you every year it applies to but it will fit 96 and 97 Landcruiser/LX450. Its the 2nd downstream cat. Magnaflow part number 23622. Will fit perfectly in place of original downstream cat. Gaskets not included which are cheap and...

Just wondering......... Has anyone blocked off the heat riser on a FJ40 2F stock exhaust manifold either using a block off plate or welded a plate over the heat riser opening and installed the stock intake and exhaust independently without bolting together? You would need to grind the bottom...

I'm looking for some advice regarding the exhaust manifold surface that mates to the heat riser/intake. Do I need to clean up the surface any further(see pictures) or will the gasket compensate for the irregular surface? If so, what should I do to clean up? I do plan to eliminate the heat...

I recently changed tires on our hundy from Toyo ATIIs to Michelin LTX MS2 to quieten the ride down a bit for some long trips we have coming up, and have discovered that we have a pronounced droning noise at 2500 rpm - which is unfortunately right at our cruising speed of ~ 70 mph. Drone starts...