exhaust

So, a couple days ago I cleaned my TB and intake with TB cleaner and Seafoam. Everything has been fine but today, after driving all day without issue, I accelerated from a stoplight and white smoke began billowing out of my exhaust for a good 50yds. It was thick white smoke and it hung around...

Hi there, I have a mild/moderate exhaust leak on the left side that goes away when warmed up. I've been reading doug thorley header threads, and noticed a couple that just turned out to be loose bolts, not cracked manifold. How involved is it to check the bolts, or is it one of those things...

$350 plus shipping. View more pics. Have lots of other FJ40 parts available. See pics. Keywords: 1965, 1966, 65, 66, FJ-40, Early, F, 4-1, 4 in 1, TEQ, big window carb, exhaust, pipe, manifolds

Im running a stock 1fz-fe, and it's time to replace my muffler. I'm considering going to 3" pipe all the way out. Was wondering if 3" would be beneficial at all, or just a waste of time and money. It's just that as I'm shopping for big can mufflers, I notice the 3" and 2.5" aren't much...

Hey guys.. i own a 1994 80 series land cruiser.. i have a 1hz non turbo engine.. so yesterday i removed my muffler and installed a new muffler.. the sound is really riced i dont like it.. so a friend of mine suggest me to remove the muffler and keep it straight without the muffler.. is it a good...

Just a ton (ouch) of china companies putting these out now. But i like the roll up traction aids at these guys site, and they have snorkle kits for all cruisers after 80's. China Snorkel manufacturer, Wheel Spacer, Air Jack supplier - Telawei 4x4 Off-Road Accessories Factory Telawei 4x4...

Took my 1hz's old Genie headers off yesterday - they have a fair number of weld cracks and pinholes due to rust/age/vibration/etc. all of which couldn't be seen without removing them. To be honest, they are pretty ugly and one of the weld cracks was 1/2 way around at a join where three cylinder...

Anyone have the FJ62 exhaust center pipe (between the cats and muffler) from an FJ62 laying around that's in decent shape? See pic.

Hi, '74 FJ40 with original F155. I just noticed a fluid leak from or near one of the bolts connecting the intake and exhaust manifolds together. The obvious thought is gasoline, which it smells like gasoline, but it doesn't evaporate like gasoline should (no, i haven't put a match to it)...

So Cal Nice clean one that goes behind cat to bring the twin cats into one pipe. $40 + shipping. Paypal OK

The guys at ACC Garage are working on new header-to-resonator replacement exhaust kit. Here are some teaser pics of the first install. I neglected to get a pic of the muffler, but it is nicely sized and surprisingly quiet. What I know about it at the moment: Maintains EGR port at rear of head...

SoCal. Prices from $25 per item to $100. Shipping is available, but can be costly. However total cost will still be much less than new. From a Local car with no rust issues - Exhaust Manifolds Heat Shields Headpipes Y pipe Dual Cats Cat Heat shield 02 sensors Resonator etc. Send message...

Does anyone have the following "J" pipe nut shown in the picture below?

Hi, I was looking for some part numbers related to my Driver Side exhaust manifold replacement on a 2000 Land Cruiser. It was lots of fun to take off, but i'll save that for another thread. 1) here are 8 nuts that hold the exhaust manifold to the engine. I'm not replacing the bolts because...

I have two exhaust leaks, including one at one of my down pipes. The exhaust was new about 4 years ago but RJ's Muffler on Capital Blvd. I have had to return every year since to fix little things. They have covered all at little to no cost, but I'm getting tired of returning every year...

First off, this is my first post but ‘Mud has been a massive resource for me these last few months. In the last year I acquired a 92 FJ80 and since I’ve slowly been building him (“Lando”) up. So far: water pump, belts, hoses, power steering pump/pulley, PCV/grommet, tires/wheels (Duratrac...

Forced Air Technologies Review “FAT” mistreated my vehicle & left paid work unfinished I have never written a negative review before but I feel that Forced Air Technologies and its owner Robert Ansick have mistreated my vehicle and their customer so egregiously that they warranted this review...

If any of you have some old California legal Downey headers laying around or know someone else who does, and wouldn't mind making a few extra bucks, I'm in the market. And by that I mean I really need some, since apparently a machine shop can't resurface exhaust headers because of the no. 1 and...

2f bolts?? by Rkbaseball posted Jul 27, 2017 at 10:00 PM Does anyone know what the bolts on the heads above the exhaust manifold are for? There is one bolt for each cylinder and they are directly above each exhaust port. They are circled in red Thanks!!

Looking for a 75-78 FJ40 Exhaust Downpipe or at least the flange connector at manifold. Let me know if anyone has one. Shipped or local pickup to 18901.