connector

Hello. I've been lurking around this forum for a few months, gaining knowledge/info & decided to join. I Just got my first TLC (2021 model) after replacing my '03 Chevy Tahoe after 275k miles (and still running). Anyway, I went on a ski trip with the family & dog and decided to remove the...

Hi everyone, new to the forum and just picked up a 99 LX470. Working on all the baseline items and this forum has been an incredible resource. I had to replace the drivers side outer headlamp and when I took it off, I found this electrical connector not connected to anything. All the...

Hey experts, I need some help troubleshooting my wiring, I swapped my 1HDT to a 6BT a year ago, and during the process when the transmission was taken down, the same smashed the plastic connector of the transmission harness, specifically this one: For some reason, this is the diagram of a 1HZ...

I work at a new car dealership, but not a Toyota one. I've called 2 Toyota dealers trying to get the part number for the cooling fan relay electrical connector as mine is disintegrating. I've already got the relay. I guess it's a real pain to look up this connector and was hoping someone here...

This is the AC high-temp thermoswitch that fits to my 80's 1hz motor. The AC has never worked since I got the 80 in 2011. I replaced this switch a while back as the original one has been damaged. Wiring harness to it is also damaged and has no mating connector. Can anyone tell me what the...

Help! Can someone please tell me what/where the green connector circled in red goes to? It comes off the wire harness located on the passenger fender near the igniter/coil on a 5/1977 FJ40. Thanks! Jeff

So when doing the inner manifold gaskets up top mechanic unplugged a connector which he called the VVT Cam sensor bank1. But I have called every place imaginable and I think he is mistaken on what sensor it is. It is a 1 way/wire pigtail in which he has stuck in the hole with out the clip until...

Wanted, R/F fender flare and connector to running board for a 1997 lexus 450. Fred, WI

I'm slowly converting from an H to a 3B in my HJ45. The donor 3B's EDIC has the newer round type connector on it and my wiring harness is the older square type. Anyone have a harness available that they can clip about 6 inches off of with the plug on it? Thanks.

Using a 24 volt 3B EDIC motor and a 12 volt 2H EDIC motor, I wanted to see if I could make a 12 volt 3B EDIC motor. Seemed physically the same with the exception of the arm orientation. So, I decided to perform a partial tear down to investigate. Here's what I've discovered so far:

Was giving my 100 a bath today and found what I think is a yellow hose connector above my skid plate? The arrow is pointing to where I found it. Caught me off guard and couldn't find anything out of the ordinary? Anyone have some insight? or suggestions?

Any ideas of the purpose of this connector?

For details on why I need this take a look at my other thread. 93 80. Anyone Ever See the A/C System Amplifier? I need to replace some terminal that somehow have broken. Specifically the female spring like portion that pinches the male pin has been damaged. I am not sure if there is some type...

The following posts are to document the 1FZ-FE US market 80 series 1995-1997 OBD2 main engine wiring harness connectors. While this is not exhaustive in the sense that it covers every single connector, it does cover about 95% of them. The remaining 5% or so are not sourceable outside of the...

Anyone have any experience fixing a melted / corroded wiring harness connector? I was chasing down some trouble with my rear taillights on my FJ60 and fixed some problems then found more. The blue connector from the main harness to the rear harness has a corroded / melted pin and I need to...

I'm looking for the female side of the plug for the rear locker. This will be the connector that the rear locker harness plugs into. It's located on the drivers side rear by the frame. I believe all 96,97 lx450's have this even if it is not equipped with lockers. Thank you!! I have paypal...

Hiddy ho, my faithful 88 FJ62 has been sitting under cover waiting for my kid to become licensed. First time in her history (250k) that she didn't fire up today. Checked tank (full), changed fuel filter since I had a spare, jumped pins, heard fuel pump and gas hissing in fuel rail. Fires...

Curious if anyone can tell me where this wire connector goes? The other end connects to the oil filter base. It seems to be the perfect length to connect to the distributor but I cannot seem to find where it actually goes.

I was hoping someone could point me in the right direction. I am looking for a test connector similar to pic#4 that will connect to the soloneid in pic #1-3. This is a lift arm solenoid for a toro fairway mower. It is in a very difficult place to test ohms on a potentially failed unit so I was...

Hi folks, working on an 80 series, I believe the black connector is the knock sensor connector, correct? what about the green one? If anyone has any of these used or has proper part #s for a 95 I would appreciate it. I need the 2 knock sensor connectors and the green one but not sure on what...