Hi Guys
I recently replaced the fuel mixture screw on my 2F Asian carb. (The head and spring were missing off the old one.) I've always read you start off my backing out the screw 1 1/2 turns. It seems mine starts running smooth when I back out about 3 turns. Should I be worried?
Does anyone know how I can find a carb idle screw? I have an '82.
I couldn't find it thru SOR, CoolCruisers, NAPA, etc
Looks like previous owner drilled a little to far past the plug and messed up the screw. Not to mention the spring is gone. I'm surprised idle hasn't changed from driving. I'm...
I should have gone LED. I just replaced my dash bulbs with the CoolCruiser magnum bulbs and I'm now blowing my fuse. Fuse is 15 amp, but I see some circuits are 20 amp. Has anyone else gone through this? Wondering if it's safe to switch to a 20 amp.
So in removing my axles, my pinion gears slipped out of place. Now I'm trying to get the pinion gears, shims and axle spacer assembled, which is a bit tricky from under the car. Is there a video or thread out there anyone knows of that shows the procedure and tricks to use?
Should the rear axle have a tiny amount of lateral play? I was wondering if I should replace my bearings while I do my seals but the bearings look fine. I'd hate to replace good bearings only to find some lateral play is normal due to bearing to shaft tolerance.
Thanks in advance!
Joe
Has anybody used aftermarket weatherstrip, such as what's offered by JT Outfitters or CruiserCorps?
I don't mind a little modification.
I will probably replace anyway once I get the car painted, so I'm trying to avoid buying factory weatherstipping...twice.
does anyone know where exactly this seal goes? All I know is that it's an upper door seal. A pic would really be helpful. Hard to tell by sor.com diagrams.
Hi All
Need some advice. I have an '82 FJ40. I bought new seat covers from Cruiser Corps and seat bottom foam from SOR, all for the same year vehicle. Took them to an upholstery guy with lots of experience. He says they don't fit. Both manufacturers claim they sold the right product.
Has anyone...
I have an '82 FJ40. I'm trying to replace my oxygen sensor after being advised upon failing my smog.
I was expecting to find the sensor on my catalytic converter which looks like the top one in one of the two pics, but can't find it. Even the FJ40 exhaust diagram doesn't show it, even though all...
It's about time I ask the experts.
I've been trying to figure out what the second emblem bracket is for below and to the right of the TOYOTA emblem. I have a Styline Ltd, whatever that is. I haven't been able to find anything on that either.
Does anyone have any thoughts on the 2nd emblem?
I just purchased a bimini top from Quadratec after it stated it fit FJ40's. Well, what it didn't say is that I'll have to make some modifications to the channel that goes over the windshield frame that holds the front of the bimini in place.
Before I start cutting the channel, has anyone out...
Does anyone know what's missing here? I know the connector in the pic is for the horn? How does it connect to it though? Is there a short intermediate cable that goes between the two?
I have an '82
Does anyone know if the late model FJ40's (mine is '82) had lighting where the dash and door pillar meet, that iluminated the floor?
I have one on each side that I need to replace, since they have been heavily abused and are corroded. But I can't find them online anywhere. Thinking they might...
I have an '82 FJ40. I'm finding I have lots of wiring issues, including wires that have been spliced into, ones that have been cut and go no where, etc.
I'm been using the chassis manual as well as the wiring manual I bought from SOR, and I swear it seems that the two don't match up and leave me...
I have an 82 FJ40. I seem to have a lot of important connectors that lead no where. The two pics below were taken through the radio and ashtray cutouts. Could I be missing an important harness? Does anyone recognize these?
OK, I've read the other threads regarding the washer hose and how it gets routed in the windsj=hield frame, above the glove box, etc. However, I'm having trouble finding how it finds itself in the engine compartment. I assume this is through the firewall somewhere.
Can someone tell me where I...
I've found a lot of threads on placement of splash shields they seem to be for older FJ's. Can anyone with a late model FJ40 (mine is an '82) show me where the shield below goes?
I'm going crazy trying to find its home.
I've been trying to troubleshoot this one for a while. Obviously, my flasher is ok, since my emergency flashers works. Since all the lights flash, that also tells me that my lights have a good ground. I've tried rebuilding my steering wheel indicator assembly and everything looks good. The fuse...
I've been trying to troubleshoot this one for a while. Obviously, my flasher is ok, since my emergency flashers works. Since all the lights flash, that also tells me that my lights have a good ground. I've tried rebuilding my steering wheel indicator assembly and everything looks good. The fuse...