Got a weird sound from somewhere around the transfer case. Tried to film it.
It appears to be the same sound as in this tread Name that Tune!! (mystery cruiser noise) with video - https://forum.ih8mud.com/threads/name-that-tune-mystery-cruiser-noise-with-video.1111829/ But there is no conclusion...
Planning a trip to AU during june-july 2017.
We are 2 adults and 3 kids (8,10,11).
Any advice to rent a 4WD camper i Darwin?
Been looking at wickedcampers.com.au but hard to judge if they are any good.
We want to see kakadu and we also want to end somewhere near the great barrier reef to spend...
Yes I know that the meter is not very accurate.
But this is where mine climbs to at highway cruising speed.
Is it to high? Dosent seem to go higher than that.
If I am going to put a probe in the coolant hose for an accurate measure, whitch temperature is then ok?
the exhaust manifold gasket blew on my BJ42.
The 2 rear most bolt was almost impossible to get of because the heads have rusted.
So took the lower one of with a dremmel, only took 2 hours. The upper one could be removed more easily with grinder.
But now I want to replace all 8 of them.
In the...
I have replaced the injector in my 1HD-T 12valve engine with rebuild ones from a dieselshop.
But the ones that I took out had ND5460 stamped on the nozzle holder and the "new" ones have ND4350 stamped on them
In the EPC I can see that there are 4 different injectors for a HDJ80 from 1990...
Newer thought it would happen but last night my cruiser really did turn on me:frown:
Was on my way to watch a fireworks-show with the :princess: and a couple of friends when the engine suddenly died.
It could start again immediately after and was running fine in idle. Drove maybe 50 meters...
In the process of replacing my badly leaking inner axle seal I discover a deep groove in the axle. Almost 1mm deep.
Can it be repaired? I have thought about welding it and then put it in the lathe to machine it nice and smooth again?
Anyone have any experience with this?
Almost ready to start my HDJ80 for the first time after engine rebuild.
One of the tyres are flat and I have to buy 4 new ones.
At the moment it have 295/75R16 BFG AT.
Some kind af EMU, proberly 2-2.5" lift.
So I am trying to decide wheter to go with 315/75R16 or stay with the...
why use pinbolts? (Studs)
Well this question could have been asked in any of the forums but all my cruisers are diesel.
I have broken 2 pinbolts in the exhaust manifold. I have gotten the pieces out and are going to buy 2 new tomorrow.
But I came to wonder: Why are there always pinbolts...
Hi
First post in this part of the board.
I have recently bought a HDJ80 from 1993 with only 290.000km on the tacho.
Engine wasent running and seller was talking about knocking sounds from the top.
Pretty sure it was the BEB and it turned out to be.
But he has run it with no remaining...
Hi
Is there any difference betwenn right an left headlamp and headlamp "buckets"?
ToyoDIY.com
the partnumbers confuses me.
it states 2 different partnumbers for LH and RH. Is this for Right and Left Hand drive vehicles or simply ringt and left headlamp?
Bought a cheap EGT instrument but I am having troubles wiring it.
There is one cable, 2 wires, for the probe.
The there is a red and a black wire for +12v and gnd. Those are also in the included manual.
But then there is an additional red wire and a black on, than goes into a little pluck in...
Think it is about time to make a build tread.
Mostly to have all the info in one place for my self to look at when ever I try to find out what went wrong ;)
Please bare with my poor english, I will do my best to make myself understandable:)
Info: Living I Denmark where cars are pretty...
In the rebuild process I have now discovered that I didn't take enough pictures of the teardown.:whoops:
So now I can't seem to remember where the brackets that hold the hard brake pipe > Soft brake hose is located.
Anyone have a decent pic of the standard bracket location, both front and...
Doing a frame off rebuild of my BJ42, now is the time to paint.
Originally it was 857 Nordic Blue.
But I think it is to light a shade, so wanted something a little deeper/darker.
Thinking abouth 822 royal Blue, but have newer seen a J4 with that color.
Any one have a pic?
Now is the time for ordering that bestop Supertop for my BJ42
I have seen tops4less.com
Any one seen it cheaper? Need a top and maybe doors.
And need it shipped to Virginia as well
Thanks
Hi
Bought a Pro-Tools 105HD together with a 50mm metric die set.
Metric because I can't get 2" tubing here.
But I got a 2" die set delivered.
I thought that it proberly wouldnt matter, why else would they send it to me?
Now I have started bending tube and my 50x3mm tubing are flattening to...