After living a few years down in Costa Rica, Selling the 6BT60 while we were down there, the heat got to be a bit too much for me so we ended up moving back to the states.
Shortly after coming back to the states we had to pickup some new vehicles and unfortunately there wasn't much available...
I have up for sale a 1977 Toyota BJ40.
Whats new:
Body completely redone with new METAL panels, not just bondo smeared on the exterior and painted.
Frame completely cleaned and painted, no rust as well.
Brakes all new (Master and slave cylinders, shoes/pads)
New Clutch slave
Rebuilt alternator...
Well I knew it wouldn't be too long before I got the Cruiser itch again and here in Costa Rica there are tons of cruisers to be had.
I found a really good deal on a local cruiser and have decided to jump on it.
It is a 1977 BJ40 with a fully restored body.
It has the original...
I am in the process of selling my Cummins 6BT powered FJ60 and am looking for a new project vehicle.
I am currently Living in Costa Rica and have access to BJ40 and BJ70 Series trucks.
I have no idea what engines can be found in either of these groups and could use a hand getting an idea...
I will be back in the states from Oct 12th to Nov 2nd, During this time If i could get it sold It would be great. If not I will have to wait until the next trip to try and set something up. Located in Central NJ
Here is a basic description of the truck for those that have not read my entire...
I have up for sale the axles I had under my truck for its stage 1 build.
Front axle:
Trussed & Armored FJ62 axle
Set Up For SOA
Cut and Turned
4.10 Gears
ARP knuckle studs
Trunnion Bearing Eliminator Kit
High Steer
Freshly rebuilt
4Runner Caliper Upgrade
Fully Dressed
$750
Rear Axle...
I am putting up for sale my family owned FJ60.
I currently have a project truck of my own and no time to work on this one.
Original owners, 179,985 Miles. Has been passing Jersey Emissions for the past 26 years and has a current inspection sticker.
Hast typical Northeast rust on fenders and...
I have 5 35" km2's in NEW Condition. I put them on my truck but it only made it 20 miles tops before the motor Blew. Now I am looking to upgrade to some larger meats.
They are mounted and balanced on 10" wide 16" diameter Blackrock Rims. They are 6 lug rims.
Looking for $1400 or open to...
I am going to be helping out a friend install a 2" ironman lift on his truck and am looking for some rough estimates on how long it will take to install.
I have access to a full shop with everything except a lift.
Any input would be appreciated. Thanks in advance.
I am redoing my front suspension on my 60 and a looking for some suggestions for which springs to use up front. I want to use the rear leafs from a vehicle and don't mind making up a hybrid pack.
Any input/experience would be greatly appreciated.
Earlier tonight I had my old 2F seize up on me while I was driving. Unfortunately this forces me to go ahead with my planned diesel swap way ahead of schedule. I had wanted to run my current setup for more time, at least for the summer but sometimes things happen that you just can't...
I am going to attempt changing the main bearings of my engine while the motor is in my truck. Are there any issues or problems I should be aware of?
Are there any tricks to this?
I have a 1987 2F motor.
Hello there, I need to repair my crankshaft pulley due to some wear on it.
I was wondering if anyone who might have one laying around could grab some dimensions off of the keyed shaft area so I could weld mine up and then turn it down again. What I am interested in is the OD of the shaft...
Since I didn't see a thread for selling parts in this clubhouse I figured I would start one:
I have a bunch of parts available for sale.
Axles, leaf packs, smog equipment, fj60 ps pump, driveshafts, Tie rods, stock steelies and a bunch of other stuff. I am looking to part with this stuff...
I am in the process of reconnecting my fuel lines. but I forgot to mark which one is the supply and which is the return line.
If anyone could let me know I would greatly appreciate it.
I am in the process of buying some new shocks for my recent SOA, and was wondering what valving to get for the shocks.
My front suspension is an SOA with rear FJ62 springs with an additional AAL, a custom front bumper(kinda heavy) and eventually a winch.
For this I was thinking about running...
Title is pretty much self explanatory. Anyone running BBC Shocks on their truck?
If so how do you like them? Any problems or concerns?
I am trying to decide on the shocks I want to run, and came across these.
I am looking for a divorced NP205 for a project I have going on.
I am located in central NJ and would be willing to drive for a good deal.
The case must be passenger side drop.