I have been trying to figure out where this wire goes and can't quite nail it down. It is coming out of the main harness where the starter harness branches out it is red with a white stripe about 4" with a small eye. There is a plug on the fire wall on the engine side can't remember if it was...
Trying to finish up my restoration, on my fifth year fourth kid through high school and so on. Can not remember what exactly this did .
I do remember it was inside next to the fuse panel, any help would be greatly appreciated. Here is a picture.
Trying to finish up my restoration, on my fifth...
Finally got the booster installed thanks to "MUD". Working on pedal linkage for clutch, making offset arm attached to existing clutch arm. After 4 years I might get this done this year, getting close.
I am trying to get my disc brake conversion completed. I have a 93' forerunner booster that I want to mount flush against the firewall but it covers the clutch master cylinder. What else works, Ive read that some use a geo booster. Are there any other toyota boosters that are smaller than 10" dia.
I am trying to plumb my vaccume lines to my fwd shifter and have no clearance to the frame. Are there any suppliers that have an elbow with the m10X1.25 threads. Any suggestions would be welcome.
I am trying get my 1.5f engine fired off before mounting body to frame. I had the engine runninig for a while about 2 months ago but had some leaks on carb. Finally got carb fixed and mounted, reconnected the the wires and no spark to dist. The positive terminal on the coil is arcing to the...
I have a 74 1.5f engine with an aisian carb that I rebuilt and have a question in regards to the accelerator pump shaft. Is there anything else other than the rubber boot over the top of the shaft that keeps the gas contained. It did not have any thing there when I took it apart but it seems...
These are the original seats. Front seats are in good shape all parts working. The jump seats open and close spring mechinism still working. Some surface rust on inside of bottom cushion panel but still in good shape.
I also have the front and rear axles that I have swapped out, these...
I am swapping fj 60 hubs onto some 72' axles and in the process of going through the 3rd members. I need help locating the specs, my manual gives no specs on 3rd members. I got some numbers off the nitro link but still am wondering what the preload on the case is. I have done some on off road...
What is the correct way to post a thread, I notice that the few times I have done it my post comes out in small case letters. I am hoping to have big letters some day. Could some one show me the way. Thanks.
I am trying to mate a sm420 to a 74' 4 speed t-case. I have been trying to get an adapter from EBI with no luck. Has any one tried to machine one recently, I would like to try. Also can some body tell me how the output shaft from the tranny(2 1/4" long) will carry the drive gear in t-case, with...
I am starting to put the body back together and need some advice on best place to find window gasket seals. I have a folding back door with slide in rubber seals and the smaller windows. The old ones slid out of these groves on the top and bottom of each panel. On the windows I don't know if...
Me and my boyes have been wire wheeling and scraping all weekend getting the frame as clean as possible in order to coat it with some rust paint. We ended up using chassis saver on it and it turned out pretty good. Thanks to some reading of past threads it made the whole job turn out o.k. We...
I am getting ready to make a full cage for my fj40 and need some advice for thickness and diameter for the pipe. I have stock seats in the front and a bench in back from CCOT. I havn't been able to figure out the best size from the tech info.Brickstone
I need some advice on how many degrees past or before verticle to position knuckle. I have read some of the tech links which say 4-6 degrees. I will probably run 35 inch tires. slowly learning:bang:
I need some help with frt diff angle. I've read in the tech links that with a carden joint at the transfercase the drive line can be in line with the pinion shaft. Will this minimize the u-joint action. Confused brickstone.