Search results for query: *

Forum search Google search

  1. bj461a

    Striped 40?

    My 5/73 with Stripes
  2. bj461a

    What have you done to your Land Cruiser this week?

    Got parts to install my stock carb and air cleaner thanks to "ToyotaMatt", who also sent my new carb adjustment screwdriver. Thank you sir!
  3. bj461a

    What have you done to your Land Cruiser this week?

    Got my new exhaust put on with the 3FE manifolds I recently installed. Ended up merging both exhaust manifolds at bell housing then using a band clamp /connection then ran it over skid plate to muffler located behind rear axle, exiting in out the rear on pass side . Was able to install...
  4. bj461a

    Need PS pump bracket source

    Your lack of finding a source is the exact reason I made one.
  5. bj461a

    Need PS pump bracket source

    I just made my own for a saginaw pump. Pretty simple if you have a welder and a drill Locates PS pump at original alt location. Very similar to the stock alt mount. Not sure abput the tercel pump, but a similar suitable mount should be something you can make if your handy.
  6. bj461a

    Need 90 degree fitting for 5/73 "F" remote oil line

    75fj40toy I sent you a pm. Thx
  7. bj461a

    Removing adhesive without damaging paint?

    Use a heat gun on that emblem to get the adhesive pliable, then use some 50lb + fishing line to remove it. Put the line under the of the emblem and using 2 hands pull it up between vehicle and emblem. It should remove emblem leaving some adhesive you can remove with a solvent suchas naptha...
  8. bj461a

    Need 90 degree fitting for 5/73 "F" remote oil line

    Have recently installed 3fe exhaust manifolds onto my stock F engine. I need to reroute one of the remote oil filter lines away from the rear manifold. I did some searching and found this thread. Wanted - WTB: Stainless oil hose or adaptor compatible with header for '68 F engine -...
  9. bj461a

    What have you done to your Land Cruiser this week?

    Finally was able to install the new to me 3FE exhaust manifolds to replace the worn out stock manifold. Lapped intake and exhaust to verify flatness to within .002" Epoxied some portions of hardened steel washers to the intake to match the exhaust manifold thickness. I could have machined...
  10. bj461a

    What have you done to your Land Cruiser this week?

    ToyotaMatt, I appreciate the response but an unsure what you mean by "unnecessary mis-alignment of your current 2 belts set up in the pulley faces" Both belts , alt and power steering pulleys are aligned and run true. Pic's may make it difficult to see this? I am using a "F" alt on the...
  11. bj461a

    Cruiser In The Snow

    Pic from 1989 despite date shown, IN and ON snow. Plywood helped keep snow from plugging air flow to rad. Good times with my dad back then.
  12. bj461a

    What have you done to your Land Cruiser this week?

    Moved my stock "F" alt to passenger side with a factory mount, belt did not line up when mounted as stock, so I made some spacers which allowed me to avoid buying a diff alt. Belt is good Then moved my Saginaw pump to where alt was. Am in process of going from the Weber that was installed...
  13. bj461a

    Post up pics of tachs in your 40s

    Sun Super tach II, in my 5/73 I do not mind not seeing the blinker light. Works for me and is out of the way of my knee.
  14. bj461a

    Saginaw pump p/n question

    What I beleive I need is the first one. Second pump shown looks to be for a "hydro boost" system as there 3 hose connections whereas I only need two.
  15. bj461a

    Saginaw pump p/n question

    1973 fj40 with stock "F" engine, removing Weber carb and home made p/s pump mounted off of front 2 head bolts. I am going back to a stock carb and air cleaner. Would like to mount a "Ham can" style Saginaw pump on lower drivers side of engine. Anyone have a part number for a Saginaw power...
  16. bj461a

    Steering lunge problem

    Do you have a locker installed? After installed a lockrite my 40, it does the same thing under hard acceleration. Most notible when turning slightly to the left.
  17. bj461a

    Please confirm a 1994 FJ80 Brake Master Cylinder and Brake Booster will fit on my 1973 FJ40

    I converted to front discs a while ago, am now wanting to replace my booster and master. Am looking at the recommended offering from City Racer. Question I have is, where do the wires that hook to the bottom of my stock master cylinder go when installing the newer FJ80 master cylinder? I do not...
  18. bj461a

    Wanted 3FE exhaust manifolds and heat shields

    Price shipped to Enumclaw WA for a set ?
  19. bj461a

    For Sale F motor parts

    air cleaner bracket that mounts to cyl head shipped to 98022?
  20. bj461a

    SOLD 1F air cleaner (MD) ***SOLD***

    Great thank you. Been wanting to get rid of the Weber and go back to stock.
Back
Top Bottom