Search results for query: *

Forum search Google search

  1. coldtaco

    What did you do on your 70 series today?

    I have been chasing the same. Only things not been replaced are the wheels, which might be happening soon.
  2. coldtaco

    New to the forum, g'day all

    Lovely, welcome.
  3. coldtaco

    Lug nut not tightening

    I’ll double check them with one of those thread pitch tools tomorrow. Or maybe the mating surface of the wheel hole is out of round or not same size anymore?
  4. coldtaco

    Lug nut not tightening

    Got one/two lug nuts that don’t seem to want to torque down. What would cause that? Nut stripping? Stud stripping? Thanks
  5. coldtaco

    Saudi 75 Too - Tilda Bogue Service Station

    I think the Scheelman are a mixed blessing for the 75 Ute, if you are short or have short legs they will probably work, if you are tall or have long legs they may not be a good fit. I ordered another set of planted brackets in bare pieces and shortened the legs to get the whole assembly as low...
  6. coldtaco

    Builds 2001 LC HZJ78 AK -RESTORATION- For Overland

    Or you could just buy one from Espar 😉
  7. coldtaco

    HZJ73 fan blower switch replacement

    What’s the problem that you want to remove the fan switch? Lots of times the problem with fan not working or only on some speeds is the resistor mounted on/near the fan itself
  8. coldtaco

    HZJ73 fan blower switch replacement

    Fan drops out of the bottom of the housing
  9. coldtaco

    Builds AK HJ-75

    🤷‍♂️ I expected that too
  10. coldtaco

    Unknown wire

    I don’t have my 2H anymore so I can’t help. Do you have a maintenance manual with the wiring diagrams? That should help.
  11. coldtaco

    Clutch booster help sourcing

    What kind of specialist shop?
  12. coldtaco

    diff temps when driving

    Ring and pinion is original, that is they weren’t replaced. Bearings were replaced and a solid spacer was used. What parts exactly need breaking in? The bearings and/or ring and pinion? Thanks
  13. coldtaco

    diff temps when driving

    anyone ever measure diff temps after driving hwy speeds? I had the rear diff rebuilt with electric locker and today was the first time to drive it at hwy speeds, for about 3mi. after getting back I felt, then measured the rear diff temps and they were around 115F. also seem to have a growl...
  14. coldtaco

    Builds 1995 HZJ77 wagon build - Japan sourced

    did those wheels clear everything in the front without the spacers?
  15. coldtaco

    Builds AK HJ-75

    Swapped in the old transfer case shift lever, now it shifts like before, the one on the right
  16. coldtaco

    Clutch booster help sourcing

    you could go with a non-boosted type. my ute came that way and I drove it like that until I did the rhd to lhd swap. I still had my boosted one from the bj70 I parted out. then when ever its time to replace your clutch you could go with a uniclutch which has a softer clutch, but still good...
  17. coldtaco

    Builds 1988 BJ74 “Number 1”

    I’m running what I believe to be 1/4” spacers in the front, Charles had swapped out the lugs with longer ones
  18. coldtaco

    Builds AK HJ-75

    8 yrs already 😳🙂
  19. coldtaco

    New joiner, French Alps with LJ73

    you would have to compare side by side between the round headlight and square headlight front end. just going from memory I would say you would have to change fenders also. carpets/interior options I think would only be newer 70 series which should fit I would assume. search on here for...
  20. coldtaco

    Builds AK HJ-75

    yes, not smart enough to cut out one piece and bend to make it like I wanted
Back
Top Bottom