Search results for query: *

Forum search Google search

  1. R

    power steering pump pressure valve?

    I was thinking of blowing out the lines with my air compressor first to see if there's any build up or crudd and checking the switch. Not sure what else could be causing the line to pressurize like that.
  2. R

    power steering pump pressure valve?

    I was thinking of bleeding, then blasting out the lines with my air compressor. maybe some buildup is affecting the pressure, but it could be the pump itself acting up. One way or the other, I need to figure out why its pressurizing the line.
  3. R

    power steering pump pressure valve?

    I did double hose clamp it originally. my first "fix" I used 250 psi fuel line and double hose clamped it, then it split open. The hose I have on now is 400 psi line, but it will not go on far enough to double hose clamp it. I drove it for about 30 minutes, then tried again to see if it would...
  4. R

    power steering pump pressure valve?

    Thanks Hornd. I read the post and failed to find anything pointing out a pressure switch. Would you mind pointing out which picture or page its on?
  5. R

    power steering pump pressure valve?

    Howdy, ive got a 93 that im having some issues with. The return hose blew out about a month ago, so I replaced it. A few days later, the hose blew off without damaging it, then again a few days later. I double hose clamped it on each end and had no sign of issues for a couple weeks. On my...
  6. R

    o2 sensor wiring

    https://forum.ih8mud.com/threads/o2-sensor-replacement-1994-fzj80.118555/ found it.
  7. R

    o2 sensor wiring

    howdy, i've got a 93 cruiser and replacing the outer 02 sensor. I have a sensor that has no plug on it and requires wiring to your old plug. I can't seem to find which ones are the heater, ground and output wire on the rig. one is white, one tan, one blue, one grey. I believe the blue is...
  8. R

    distributor don't fit.

    I ended up with recentered trailworthyfab rims. They are HEAVY, but were well done and powdercoating is quality. They are a bit slow in service and had 2 out of 5 tires that had punctures. They were happy to send a replacement for one that had sidewall damage and offered up repairs for the...
  9. R

    distributor don't fit.

    he he, i feel pretty dumb right now. I figure that out just after i posted. I checked the sensor and was getting power, but seemed to be broken. I replace it and everything is well now... other than the bolt for my oil level sensor. :doh:
  10. R

    distributor don't fit.

    hmmm, maybe i'm not going to replace the oil sensor today. 2 out of 4 small bolts wont budge without stripping and one broke. On the plus side, one came out just fine.
  11. R

    Help with rust inside vacuum system

    i replaced my egr after finding it was rusted shut on both ends. I replaced the rubber hoses and shot cleaner thru the manifold and brushed it up, then blew some air through the modulator to make sure it was able to pass thru. Mine was a washington vehicle so i knew moisture was going to be...
  12. R

    distributor don't fit.

    well, i'm running 37's and h1 rims, so the power steering never feels quite adequate, but normal nonetheless. The gauge does not rise and fall, just stays put. The connector seems to be ok, but haven't ran a tester on it yet or pulled it. As soon as the temp goes up a few degrees here, i'll...
  13. R

    at temp, brake and oil light on

    no problem :beer:
  14. R

    distributor don't fit.

    I don't have a crank wrench for this pulley, so i'll have to figure something out. i do have a torque wrench, just nothing to stabilize the pulley. You guys have any tricks? Im going to get on the sensor tomorrow. I ran it to pick up my daughter from school a couple miles away and ran a loop...
  15. R

    towing with 37's, need advice

    ive got 37's and tow. i use it towing our 21' cuddy cabin boat as well as 36's and a trailer weighing around 4k lbs full of welding gear and tools from oregon to north bay ca. Only trouble was windy roads and downhills needed to downshift, but otherwise ok. it does bog down, but its not too...
  16. R

    distributor don't fit.

    Now after replacing the cams, dis, alternator, egr valve and a load of other parts, im getting no oil pressure readings in the cab. Im looking at some possibilities, but any advice would be helpful
  17. R

    at temp, brake and oil light on

    Thanks for the advice, checked fuses, fusible links and the alternator ended up being the culprit.
  18. R

    Worlds most expensive 80?

    i dunno guys. I paid the huge sum of 2800 dollars for mine and it even came with free moss and pine needles (fresh scent). You can't buy moss growing on your rig at the store. that's got to be worth something.
  19. R

    at temp, brake and oil light on

    i just finished rebuilding the motor after a blown head gasket. engine starts and idles pretty well, but ive got a few lights on. They turn on and stay on before i even start the motor and persist after ignition. The at temp light, brake light and the oil light. When i tried to roll down the...
  20. R

    distributor don't fit.

    it wasn't supertight, but i have to imagine that i helped crack it somehow, even if the shop did drop it or improperly tighten it in (i had to remove it again to get headbolts in place). Funny, as i was sitting here, looking for a good price on cams, while wearing an old camelback toyota (in...
Back
Top Bottom