i have a jags that run vehicle speed sensor to sell. unused, it was for an engine swap that never happened. part #2prs-toy. i'd like to get $90 shipped within continental us for it.
i can post a pic if there is interest.
thanks
i was curious if any of you guys have come across a warn 8274 model, year or # that came painted black from the factory. i'm looking at buying one used and don't know if it has been spray painted or what.
thanks!:beer::beer...
hey guys,
i'm looking to mate mini truck cv driveshafts onto course spline t case and pinion flanges. i'd prefer to not buy adapter flanges for all of these. is there any reason why i can't hybridize my cv driveshafts with my old driveshaft yoke flanges? i think i shoud be able to use the same...
Rear axle, fj40, stock axleshafts and carrier, new thrust washers of propper thickness, new cross shaft, new c clips my problem is that when installing the axle c clip cap on one axle shaft, the shaft is too tall to allow the cap to sit tight against the locker gear. This problem only happens...
i'm building a spring over fj40 with fj60 rear springs. my problem is that they are too flat, and need some springs with more gumption (fj62).
pm me if you can help,
:beer:
this may seem like a crazy idea, or maybe i just haven't heard it before.
splash guards are made to keep water ( to a certain extent) off of brake friction surfaces.
with soft suspensions, 4 wheel disc brake systems commonly lock up the rear wheels before the front during hard braking/...
hey guys,
i'm getting ready to do my spring over without shackle reversal. i will be cutting and turning to give better caster and increase clearance under the pinion. what kind of caster are people ending up with? i've read everything from 1 degree stock to around 6 degrees. i want it to...
i can't find my @#^&^$% fsm. i'm pressing the bushing into the spindle but don't know the correct orientation of it.
can anyone help?
i've looked at several and found no rhyme or reason, maybe there is none.:beer:
I have a set for both front and rear of my fj40 springover. I'm not flipping the springs or doing a shackle reversal. The wheel base will be lengthened by moving the spring mount locations 2" front and 3" rear. One set has significantly more arch than the other. I'm looking for someone with...
does anyone have the measurements of the axle locating pin on each type of spring.
i know the overall lengths are roughly the same from a link i checked out earlier. it lacked the info on axle placement.
thanks all
found! thanks guys!
i'm looking to install them front and rear in my fj40. hoping to find some in the seattle tacoma area to save on shipping.
give me a pm or call tal at 206 554 1665
thanks
Hey all,
I'm putting in fj60 springs with an soa conversion and no reversal on my 40. I'd like to keep it a bit on the low side but still use long shackles, so I'm looking to recess the shackle into the frame on the front springs. Anyone have experience with this? I have a saginaw box up...
Correction, S10 manual master cyl. Has anyone out there used the setup in the tech links beside Mike Smythe? It sounds simple and cheap. Easier than getting a new booster and master for a 4 wheel disc brake system. I'm building with late 4runner fronts and late S10 rears. I'm just wondering...
does anyone know if 1996 to 2002 4runner brakes work with a standard mini disc swap onto a fj40 axle? i have read that the earlier model 4runner calipers work, but how about the later ones? will they have a larger piston size? i want to get the largest pistons possible along with a...
ok guys,
i've swapped in mini truck birfields and marlin tacked the inner axle about 1.5" from the end of the shaft. i put the axle into the diff. and have problems rotating the shafts. the birfields bind on the housing. i'm at this point wondering if either A) i haven't clearanced the...
i'm relocating all my pivots and such during my spring over. as i'm trying to put it all toghether, i'm wondering about the relationship between the leafsprings. should they be parallel to each other, or should they be toed in or out? it seems like the stock front springs (for example) are...
so guys,
a new-bile question for you all. i want a limited slip in the front of my fj40 for non-core wheeling. is there a reason why i can only find detroit truetracs for reverse rotation and mini truck diffs? i've read that you can install a rear true trac in the front, but it wernt...