saucebox's latest activity

Most of these connectors have a 5-digit number on them. Look at the old/current connector for the 5 digits. Add '90980' before the 5 digits and that's your part number. This works for most connectors. Picture is just an example - not the...

They are probably talking about the Eaton Detroit lockers.

Same experience here. Not a single noise, going on 5 years with an Eaton. I chose it so I could run fewer and smaller things to the front axle and not have to plumb all the way to the other side of my truck where the compressor lives. Mine...

Recently picked up a Covercraft for mine, and another for the wife's car after a similar question and a few recommendations from folks that live in Arizona. They've been outstanding. Previously had Weathertech, which got tossed when some of the...

NSXs have always been my favorite. I may get one one day. Until then, cruisers are my questionable financial decisions. Well, NSX or GTR. Either one would scratch my childhood itch.

Hit a nice round number

Wired up the license plate light. Used a Deutsch connector if I want to run without the jerry can holder.

I say make the kid ride an electric bike until he can "mature up" a bit on vehicle treatment. But fix the 100 maybe as a graduation present.

Mark your calendars and join us September 6th at the Land Cruiser Heritage Museum in SLC, Utah. Full details here: Land Cruiser Heritage Museum - CruiserFest - https://landcruiserhm.com/events/cruiser-fest

Added mud flaps to the cruiser company bumper. The fill the gaps in the body work in the fender. nicely I recommend the Rokblokz universal truck mud flaps - original size. They come as a set of 4 and would probably work well on the front too...

I have the Bump-It Offroad trilogy. They are HEAVY and have taken some huge hits which is obviously a good thing, but the weight makes it hard to get them off and back on when needing to get to something they cover. My suggestion is sort of a...

Same, but I had the full set of Slee steel plates. There was no change to mileage numbers whether they were on or off. I presume a difference in acceleration or braking, but it was never noticeable. Can't run the front or mid plate anymore, but...

Finally got the new hood swapped over after getting it blasted and painted, went with the cascadia solar panel as a blackout/battery tender. New moldings, bumpers, wiper plumbing, etc. Very happy with the switch to a mist type nozzle vs. the oem...

New Koozies on the site! Excited to add some new stuff, check it out! https://www.aceoverland.com/products/temporary-government

3d printed a sleeve for my swing arm latch so that it can accept standard bike grips. The longer length of this makes things so much easier and prevents me from slamming my hands into the locking pin.

Put some up for sale!

Took the ‘04 LX470 out towards Stampede Pass in WA. Easy trail with tons of beauty…

Keep it up with the beans and rice, go straight to the MRAs 😂. No experience on those specific coils, but have loved the dual rate coils they offer. Mine are CVT-485VT I think.

does anyone miss the auto dimming function on the rear view after swapping to the wolfbox?

I was less careful and got stuck in the tank traps :D

My cheapo from amazon has the indent for the antenna.

Drummond Island, MI

All four wheels are on the ground, and I'm continuing with the interior assembly—connecting all the grounds, reinstalling the floor carpet, seats, sanding, filler, prepping to paint, and so on. The front end sits higher than I'd like, but I'm...

Finished with the tubbing and waiting for the sealant to dry up in the next 7 days, meanwhile test fitting and trimming the fenders/cladding - can't wait to fire this thing up just to shut it down and do the timing belt after haha...

After we lost control on gravel and hit a tree (low speed, no one hurt), I went on the hunt for another 100 within our budget, which was not easy. I bought the one we totaled (a 1998 LX470) 9 years ago with 121,000 miles for $10,500. That rig...