ajax1's latest activity

Dry ice cleaning followed by laser and coated the axles. Next up, PDR. Any recommendations for the wheel wells now that it's stripped clean? Not sure what used to be there... was thinking rubberized undercoating?

I had mine made, if you search you can see which shafts to get for the cv, or buy slee or land tank

No argument that this is a good idea. I thought about it but didn't want to lose a day waiting for the paint to dry, and I convinced myself that since this is my beater rig I could make peace with it. Also, I was being lazy. Now that you've...

Paint the rod ends or they willl rust up quick on ya

Check your seal there is an insert inside the seal that moves down over time, you have to push it back up to its proper place.

Drove the LX450 to a meeting in Chattanooga, TN today. A total of ca. 250 miles knocked out and with the throttle body, TPS, and cables dialed in plus having the timing set properly it is running very good. Previous mileage with retarded...

Make sure accelerator cable is not sticking, next time it high idle put your foot under the pedal and pull towards you and look and see if throttle body is at it stops

I would also check that your TPS and IACV are in spec and working properly (I've been beating a dead horse with that advice... lol... because it solved the problems the rig was having... which were very much like yours). While you are...

I'm patiently waiting for a hand crank downgrade kit.

Where you overcharged ? Did Dissent refuse to refund you if you were ? . Or did you just see mistakes on their site and point them out? Then were not satisfied they did not fix the in a time frame you liked ? Dude most Land Cruiser company's...

@AdamFire You right. I don't know s*** 🙃 On my ad, please ask questions if YOU are trying to buy, then DM me for negotiating. If your not trying to buy. . .thank you for viewing th ad 😉

There are usually some on EBay parts, i found a single white 96 for mine, at that time there were a few used full sets.

Doesn’t sound like you were set in timing mode

54

I’ll keep reading, mostly to find out how many more posts it will take to replace a failing/defective radiator. Good luck.

I have a JDM/australian spec 92 . It came with full float rear with disc brakes . But the rotors for the 93 onwards are bigger (diameter: >92 315mm 92-98 336mm) Tryna figure out which parts are the different ones between these models

91 92 come with semi float rear, some 93s have them then in 93 changed to full float, different brakes You would need to install a full float axle to get the disc brakes in back.

I have done 2 in car head gasket jobs, and they kind of sucked. I agree with the others here, just pull it when the time comes. That said, I wouldn't rush it as long as your HG is intact now. Just be certain every heater and radiator hose is...

I detailed the old girl up and took her out to a local lodge for a couple beers on the deck. I dare say, she was the purdiest rig in the parking lot. :)

Ignition fuse for me. Crazy. Up early for work and didn’t even think to check when it died. That same fuse went through the laundry a few days earlier hahaha

I got code 420, reset the code, bout 6 months later wife complained of f lack of power and truck being loud, bout 8 months later cat clogged blew the y pipe, no power on the hwy. Replaced with used y pipe with 175k and two used cats. Replaced...

My old Magnaflow system to my new one. Fit was excellent. Still nice and quiet. Changed out due to a cracked weld on muffler, rusted out bracket on muffler, and what was thought as a clogged cat. 89K miles in 6 years.

I have very recently replaced my exhaust system, except for the resonator pipe. I bought Magnaflow (and BRExhaust made by Magnaflow) from Summit Racing and I bought all hardware, gaskets, and cushions from Toyota. The Magnaflow exhaust is all...