Universal, 40, 45, 55, and 80 series TEQ badges for sell

[bhicks]

Here's the link to the thread in the 80 section. Pics and info are located there.

https://forum.ih8mud.com/threads/teq-emblems-finally-ready-to-sell.802659/

If there are any 40 series, 60 series, 100 series, etc. etc. owners that would like something similar then shoot me a PM and maybe I can make a batch for your specific model.

 

[bhicks]

The first batch of orders were sent out this morning. The rest of the orders should go out tomorrow morning. It looks like the TEQ badges for the LX and 95-97 Yota were the hot ticket. I only have one left. I do have a batch printing right now, and will do another batch during the night. Give me a couple days to build up another good size batch and I will then update the ETSY page. I just don't like putting items up for sell unless I have them in stock. I'm trying to avoid any large wait times. Thanks for all the support guys.

 

[bhicks]

Update: I ran out of the Grille TEQ badges for the 95-97 Yota and the LX450. I just finished a batch of 6 LX450 TEQ grille badges and was able to update the ETSY page. It no longer reads out of stock. I have more 95-97 Yota TEQ badges being made right now and will have a batch ready to go onto my ETSY site in the next couple days.

 

[newtomelx]

Just ordered one in red for a '97 LX

 

[bhicks]

Just ordered one in red for a '97 LX

It was just put in the mail. If you haven't received the tracking number yet, you should soon.

 

[bhicks]

I figured it was time for an update. I just got the last order shipped off. I can finally breath again. I apologize to the few guys who had to wait a little longer for the 95-97 Yota TEQ badges. I went through 5 days, 2 spools of filament, and 11 failed prints before I finally realized what the problem was. I got new parts ordered and will be printing more TEQ badges soon. I decided to print the last few orders in the PRO PLA instead of the standard ABS. My machine can handle the PLA with no issues. It's the ABS that has been killing my machine. The PRO PLA is quite a bit more expensive and should last a long time. I just wanted to get the orders out asap. My zero profit margin turned into a loss when I switched to the premium PLA, but at least I am caught up and can take a breath. If anyone has any issues with their emblem then shoot me a PM and I will get it taken care of. Make sure you guys read the install instructions on the etsy site. You do not want to over torque the screws going into the plastic tabs. BTW, I do have the 91-94 Yota TEQ badges in stock in both colors, and the LX450 TEQ badges in stock in both colors. As soon as I get the heater parts I will repair my machine and continue printing the 95-97 yota TEQ badges in ABS. I just can't continue using the PRO PLA. It's stupid expensvie and I would have to substantially increase the cost of the emblems and I don't want to do that. ABS is the standard plastic used in automotive applications and should hold up to the elements quite well.

 

[NLXTACY]

you should add a link to these in your signature.

 

[bhicks]

you should add a link to these in your signature.

I hadn't even thought of that. That's a fantastic idea. Thanks.

 

[bhicks]

Update: my machine is repaired and I'm back on track. I have a good size batch now ready for round 2. My etsy page has been updated. Here's a pic of what I have. There are 4 more 95-97 TEQ badges coming off the machine now and 4 more LX450 badges getting ready to start. Tonight and tomororw I wil print up a new batch of the universal Flat badges since I only have a few in each color.

https://www.etsy.com/shop/BH3DPrinting

 

[bhicks]

I need an update from you guys. I have now shipped all open orders and have fully restocked all of my TEQ emblem options. For the first time in a long time my printer is resting. I need to know who is planning on buying a TEQ badge in the near or distant future. Either post on my for sell thread (https://forum.ih8mud.com/threads/teq-emblems-finally-ready-to-sell.802659/) or shoot me a PM if you want to buy a TEQ badge. I need to know if I have enough in stock to meet those orders. If I do, then I can now shift my focus to the "80" and "TOYOTA" grille emblems. It will take me a couple weeks to get a perfect print file set up and a good batch of each made.

 

[Island Hopper]

Just a dumb question, I have a 68 fj40, would one of the red and white grill badges work with my grill?

 

[bhicks]

Just a dumb question, I have a 68 fj40, would one of the red and white grill badges work with my grill?

No, but if I had access to an FJ40 grille then I could make one that would be a perfect fit. Whoever wanted to loan me their grille for a couple week I would be happy to toss in a free emblem and cover the cost to ship it all back.

 

[Island Hopper]

Hmm, I just might ship you mine....

 

[bhicks]

Hmm, I just might ship you mine....

Just shoot me a PM if you want to work something out or if you know a local Socal 40 series guy that would be willing to help me out.

 

[bhicks]

Update time: I got the next badge ready to go. I'm not sure this will be a popular one, but I had enough interest to at least do one batch of 6. I will do another batch if needed. I will only be offering them in the two color combos. They are already on my etsy page and ready to ship out. This is a rear hatch TEQ emblem that can fit on any year 80 series. It can replace the factory "sombrero" or the "L" OR it can be placed off center (leaving the factory emblem). It can slide left or right as far as you want but not up or down. The new emblem is curved on the back which matches the curvature of the rear hatch at that specific elevation on the door. I didn't add the factory "tabs" to this so it could be mounted in numerous locations AND on an LX or YOTA. The factory tabs were super tiny and pretty much useless. The install instructions and more info is on my ETSY page. Here's some pics.

 

[bhicks]

I wanted to give another update. I have a little gold/champagne filament left over from a custom print I did for a member. I went through 3 failed prints before I got the correct temp settings all dialed in. I had not used that brand of filament and every brand has their own unique printing issues. Once I got the order filled I realized I had a little left over to do a few more prints. If anyone wants a black/champagne color combo of any of my designs on ETSY just shoot me a PM and I can make it happen. You can order the emblem through my etsy page. Just make sure you leave a note on the order about color preference and send me a PM first to ensure I still have some gold left. I can do a black background with the champagne text or a champagne background with the black text. I will be able to do this for as long I have the gold filament. (which wont be very long) I will post a pic tonight of what the color looks like. I will post a pic of the color when I get off work tonight.

 

[bhicks]

Update time again. I am fianlly releasing my final TEQ design. This brings my total to 6 different TEQ badge options with 2-3 color options in each. This was an after thought that only got done due to demand. I had quite a few guys ask me through PM's and emails if I was going to release a more "traditional" looking round badge with a flat background. Some didn't want the honeycomb rear pattern. Others liked the pattern but not the oval shape. So here is something to hopefully make the last group happy. This can be mounted on any Landcruiser from an FJ40 to a 200 series on any flat surface. So be creative and enjoy finding the perfect mounting place for you. These are on my ETSY page and ready to ship. Finally I can move on to my other designs.

 

[bhicks]

I wanted to give an update on color. I had some demand for a black and champagne color combo so I went ahead and ordered a full spool of the champagne/gold color. I can print any emblem with the gold as the background or foreground (text). when you order on my ETSY site just leave a note and also send me a PM of the color change.

 

[bhicks]

Time for a final update on the TEQ badges. The orders have slowed down and I have made a decent batch of every TEQ badge style in every color. I am now moving on to the "TOYOTA" badges, the "80" badges, and the cupholders. What I have in stock is all I will have. I will not go back to print the TEQ badges for quite some time. If you want a TEQ badge then you need to order while I have supplies left. My hope is that I will be able to get back to making another round of TEQ badges some time in late summer or fall of this year.

 

[bhicks]

Still have everything in stock but I am down to one or two of a few of the designs.