For Sale SLC, UT: Connecting Rod Bearing (BEB's) Christmas Sale for your 1HZ/1HDT/1HDFT

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

SteveJackson

SteveJackson

10 Year
Joined
Oct 21, 2013
Threads
107
Messages
1,141
Location
Utah
Website
www.landcruisersdirect.com
Location
United States
Have you changed your BEB's lately?

Tri-metal Japanese Taiho bearings (with or without bolts) or Australian/Chinese ACL bearings (with or without bolts). Reduced price across the board through Christmas 2020.

You can order them directly through the ebay links below or contact me here on mud directly to pay $5 less. Cash, check, card, paypal, venmo accepted.

Taiho bearing set without bolts $79+shipping: Taiho Tri-Metal Bearings for Toyota 1HDT Straight-Six Diesel | eBay

Taiho bearing set with bolts $139+shipping: Taiho Tri-Metal Bearings for Toyota 1HDT Straight-Six Diesel w/Rod Bolts | eBay

ACL bearing set without bolts $39+shipping: ACL Duraglide Bi-Metal Bearings for Toyota 1HDT Straight-Six Diesel | eBay

ACL bearing set with bolts $99+shipping: ACL Duraglide Bi-Metal Bearings for Toyota 1HDT Straight-Six Diesel w/Rod Bolts | eBay

I'll give this a little time here before posting it other places.
 
Last edited:
Dang, I should have waited to order a little longer... Just showed up in the mail today.
 
Skippyd said:
Dang, I should have waited to order a little longer... Just showed up in the mail today.
Click to expand...

I didn't really have this in mind until minutes before I posted haha. Partial refund on the way.
 
These don't cross over to the HZ, correct?
 
@chapel gate @SteveJackson well, then take my money! Thanks for the confirmation... Will do some research on the difference (will be for a turboed HZ - need two sets) so advice appreciated.
 
BreckenridgeCruiser said:
@chapel gate @SteveJackson well, then take my money! Thanks for the confirmation... Will do some research on the difference (will be for a turboed HZ - need two sets) so advice appreciated.
Click to expand...

ACL was always the go-to for many of the Aussies facing the BEB issues years ago. ACL is still good, they are an Australian company with manufacturing in China. They seem to do just fine for those that use them. I prefer the Taiho's, Japanese designed and manufactured. About five years ago I did a deep dive on it, and although I don't remember all the technical details, the Taiho tri-metal bearings won out. We stock both but use the Taiho's in the trucks we sell. Happy to supply either! Send me a pm and I'll send you a total.
 
SteelHunterFJ80 said:
Do you know if the boltss must be replaced or can they be reused?
Click to expand...

Per the FSM, they can be reused if they are within spec. I have coffee cans full of used ones. I only put new ones in because a few bucks in bolts is cheaper than getting a replacement 1hdt.
 
SteveJackson said:
Per the FSM, they can be reused if they are within spec. I have coffee cans full of used ones. I only put new ones in because a few bucks in bolts is cheaper than getting a replacement 1hdt.
Click to expand...

I'd sleep easier if the same analogy was applied to preference given to the Japanese manufactured over the Chinese manufactured BEBs :)
 
1HaytchZed said:
I'd sleep easier if the same analogy was applied to preference given to the Japanese manufactured over the Chinese manufactured BEBs :)
Click to expand...

No doubt. We only use the Taiho bearings in the shop, just offer the ACL bearings because they've been a popular option for so many years.
 
You must log in or register to reply here.

Share this page

Back
Top Bottom