Metal Tech Sliders Installed

[SanDiegoCruiser]

MonkeyCruiser cruised over today and we both installed our Metal Tech sliders from cyber Monday. Took a few hours to install them both on our cruisers. I had to remove that counter weight since the attachment hardware for the middle bolt needed to go right where that metal square weight was.

Routing the hardware clamps around the brake lines was a little challenging. Unclipping the lines from the plastic holders was the only way to get the clamps under the lines. I need to notch or trim my plastic skid plate so the bolts will line up correctly on the skid plate. Not a big deal.

They are very well built sliders. Looking forward to testing them out in Anza Borrego Desert soon.

 

[ENGINE er]

Looks great, me and another mud member sailaw are doing ours tomorrow and then an afternoon of wheeling!

 

[Mxndrnks]

Let me know when that Anza trip is going to happen... I am thinking it is getting to be time for that SOCAL hundy run....

 

[Nottajeep]

MonkeyCruiser cruised over today and we both installed our Metal Tech sliders from cyber Monday. Took a few hours to install them both on our cruisers. I had to remove that counter weight since the attachment hardware for the middle bolt needed to go right where that metal square weight was.

Routing the hardware clamps around the brake lines was a little challenging. Unclipping the lines from the plastic holders was the only way to get the clamps under the lines. I need to notch or trim my plastic skid plate so the bolts will line up correctly on the skid plate. Not a big deal.

They are very well built sliders. Looking forward to testing them out in Anza Borrego Desert soon.

Are you just running two brackets now?

Those look badass. Can't wait to get mine on.

 

[CandyPants]

Looks great, me and another mud member sailaw are doing ours tomorrow and then an afternoon of wheeling!

Agreed on the looks great. Y'all are in Houston? If we haven't met, I sure would love to find out where to wheel around here. Sorry for the slight hijack!

 

[SanDiegoCruiser]

Let me know when that Anza trip is going to happen... I am thinking it is getting to be time for that SOCAL hundy run....

Thinking this Monday 2nd. It's a holiday for most...

 

[SanDiegoCruiser]

Are you just running two brackets now?

Those look badass. Can't wait to get mine on.

3 brackets. I had to remove that square weight thing to fit the middle bracket on the passenger side.

 

[Mxndrnks]

I'm down.... lets get a group going for Monday.

 

[monkeycruiser]

In for Monday.

 

[TeCKis300]

Dang, would love to join you guys Monday but don't think I can make it. In for a future trip!

 

[SanDiegoCruiser]

OK, Cool, Monday it is! I've created a new thread in the SD Cruisers section to organize this trip.

https://forum.ih8mud.com/ca-san-diego-cruisers/545431-anza-borrego-jan-2nd.html#post7221213

 

[LCbruiser2000]

MonkeyCruiser cruised over today and we both installed our Metal Tech sliders from cyber Monday. Took a few hours to install them both on our cruisers. I had to remove that counter weight since the attachment hardware for the middle bolt needed to go right where that metal square weight was.

Routing the hardware clamps around the brake lines was a little challenging. Unclipping the lines from the plastic holders was the only way to get the clamps under the lines. I need to notch or trim my plastic skid plate so the bolts will line up correctly on the skid plate. Not a big deal.

They are very well built sliders. Looking forward to testing them out in Anza Borrego Desert soon.

those look great!
how much were they, if you don't mind my asking?

 

[SanDiegoCruiser]

those look great!
how much were they, if you don't mind my asking?

$600 Cyber Monday special. I believe they are normally $800.