Land Cruiser out of Commission for a bit

[dbenke]

elect impact at harbor freight for $39 or less on sale.
Used BillWright's in G,ville, works as well as an air one, but it's bigger.

 

[ocdbeetle]

elect impact at harbor freight for $39 or less on sale.
Used BillWright's in G,ville, works as well as an air one, but it's bigger.

One at walmart too but I didnt catch the price.....

 

[BenMara]

Got an elect impact till i get aircompressor now next prob i got a good deal, but its 3/4 drive not 1/2 80 ft/lbs more Milwaukee corded impact new gota love craigslist now need an adaptor from 3/4 to 1/2 should i buy an impact one or just get regular CrV one more chance of shattering and i do have a tendency to keep the trigger down lalala

 

[dbenke]

Go ahead and get the impact. Especially w/ the 3/4 impact. It should have more torque than a chrome one will handle.

 

[BenMara]

well only could find a ol chrome one but it worked loosened all the bolts, got the pass side arm about 1/3 on no wheels on Lc to push axle forward haha anyway had some fun maybe ill do the driver side about the point but i did kill the battery so jumped it was funny havent started in over since the parade i should forgo the rear and just the front done
anyway
Yall wont be seeing much of me anymore
im on 2nd shift now lovely 1400-2230 work hours blah oh well hope he helps with my insomnia, sleep apnea, and migraines

 

[IndianDoc]

Shift's a killer

I doubt if it helps any at all and you will be missed, wait a min who are you!!!

 

[BenMara]

Well ended up filling the parts cleaner wit some kerosene, cleaned some parts, got some parts in needed to finish off the front, now i just need some time to do the rebuild, Im seriously thinkin about calling in tomorrow and working on the Cruiser

 

[Brock]

give me your bosses number so I can rat you out and get a finders fee for finding out you were playing hooky. LOL

 

[BenMara]

haha well rebuild long side birf what a pain to remove and install those birf balls not much done today

 

[dbenke]

I just got my rear axle back together. Now to get it back under the Jeep!!!

Front is next

 

[BenMara]

well it goin alot slower then i wanted and interest has been on startin another project (air cooled VW) but i do a lil work on it on the weekends, all bearings all greased, greased and reassembled axle shafts and birfields

need to do list

Clean up axle housing, knuckles,
install all bearing races
blah blah blah

install Slee arms

blah i need to quit lookin at VWs

 

[BenMara]

Well im doing it again skippin out on work to get a dent on some work on the cruiser and leave the stress of work. anyone im tryin ot get up and driving by easter well see if i can do it

 

[BenMara]

half of the bearings in, all bearings races in, diff RRed (take out the Slop that PO had in there), Slee arms installed and torqed, just have to put the front end back together so Easter looks possible

 

[IndianDoc]

half of the bearings in, all bearings races in, diff RRed (take out the Slop that PO had in there), Slee arms installed and torqed, just have to put the front end back together so Easter looks possible

Will be good to see you and big green again. How's the pups?

 

[BenMara]

their doin good, still unknown on the hounds bout wit soft poop but hes still acting postive and normal unlike me when i work

 

[BenMara]

It moves, and showin its colors

 

[BenMara]

meh damn front diff is leaking wish the bus wasnt so heavy