Parting Out 88 fj62 part out, drivetrain is gone

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

cwwfj60

Supporting Vendor
Joined
Dec 16, 2007
Threads
49
Messages
1,404
Location
San Antonio, Tx
Hey guys, I am parting out a 88 fj62 with 79,000 miles. The truck was flipped on it side so it caved in the roof busted up pretty much every panel but the hood. But the interior is in great shape just needs some cleaning, COLOR IS BROWN. So I'll start a small list of the available stuff but there is always little small odds and ends that you may need for your project that won't be listed so be sure to ask and I will pull it for you. I will post pictures if you need me too.

First off the non-available parts:
-Entire drivetrain, engine, trans, transfer case, front and rear axles
anything related to making the engine run is not available, I am swapping the motor into my 60.
-driver rear tail light lens
-master window switch

Available parts (still on truck):
-pass quarter glass
-rear tailgate glass
-rear tailgate wiper motor and nozzle
-front wiper motor
-front grille chrome is a little rough but no cracks
-front drivers headlight grille no cracks

Available pulled parts:
-both front seats, in great shape just a little dirty, no tears or anything, frames are rusty and will need to be replaced
-SOLD - rear bench, also great shape just dirty. - SOLD
-drivers front window glass
-pass and driver rear stationary window glass
-SOLD - all 4 electric window regulators, tested and working - SOLD
-SOLD - 3 passenger window switches, tested and working - SOLD
-all 4 door panels with associated parts, good shape
-rear seat belts
-center console heater switch and rear floor heater
-factory radio, turns on but buttons are worn and don't function, I don't know if this is worth anything but would be cool if you could have it repaired, I would love a factory radio for my 60 but they are $$
-rear speaker grills, pass side in good shape, driver side plastic part is slightly cracked
-pass front and rear door belt moldings
-all door seals, used obviously but as low mileage they could be a cheap fix for your worn out ones.
-SOLD - all the door latches and lock actuators tested and working - SOLD
-SOLD - complete floor shifter, rusty but all there, the sliding gate is a little goofy but it's all there

This is all I can think of currently but I am working on it off and on and will be happy to take pictures of whatever your interested in. I plan on cleaning the seats soon and will post pics soon. Just make me an offer, I may add prices to all of this but time is an issue. I have a good idea what most of this stuff goes for and have done a little research so don't expect free stuff but any reasonable offers will be considered.

Thanks,
Cody
 
Last edited:
how is the fuel filler neck? IE is the lip all cockeyed like mine, or does it seal when you put the cap on? I am looking for one that seals and does not have a buggered lip. Also interested in the fuel vapor seperator providing it isn't compromised...will need these shipped to 93722...thanks.
 
mirrors didn't survive rollover...or any other body panels for that matter

all door electronics (window motors and lock actuators) are sold, also rear bench was sold
 
PM sent on rear heater assembly.
 
Mr. Tibbs

Here is some pics of the glove box door, only issue is the three small rust spots on the bottom edge of the door, very small, hardly noticeable, tried to get a good shot of them but couldn't. Let me know what you think, also sent you a pm.

And it's backwards because I used my laptop's camera

Photo on 6-1-15 at 5.21 PM.webp
Photo on 6-1-15 at 5.21 PM #2.webp
 
I'm interested in the front grille and if you have it the rear license plate assembly. PM me with price and pictures:)
 
Ok on the license plate assembly, I do want the grille. I'll PM you with my phone number you can text if you can.
 
Ok on the texting, can you post a pic of the front grille? How much would you like for it?
 

Users who are viewing this thread

Back
Top Bottom