1996 Toyota Land Cruiser
- Thread starter Expolander
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
- Joined
- May 19, 2008
- Threads
- 61
- Messages
- 368
- Thread starter
- #83
I only have a set of stock rear springs available. Fronts are sold.
Sorry, I do not have this part avail.
Thanks.
- Joined
- Jan 22, 2003
- Threads
- 276
- Messages
- 1,581
- Location
- flagstaff, Az , 86004
- Website
- www.adventuredriven.com
Looking for a computer and a coil ignighter for a 96 Land Cruiser. How much to 86004 AZ
Thanks
Sethro
Thanks
Sethro
- Joined
- May 19, 2008
- Threads
- 61
- Messages
- 368
- Thread starter
- #85
Hi Sethro,
I'll check into this. But to make sure I'm going after the right parts for you, would you please send me a picture, part number or something to help identify more exactly the parts you need.
Thanks,
Tim
I'll check into this. But to make sure I'm going after the right parts for you, would you please send me a picture, part number or something to help identify more exactly the parts you need.
Thanks,
Tim
still have headlights and grill?
- Joined
- Jan 22, 2003
- Threads
- 276
- Messages
- 1,581
- Location
- flagstaff, Az , 86004
- Website
- www.adventuredriven.com
the main truck computer is behind the glove box to the right, here are some photos of the other part I want. the ignihter is located to the right of the master shown in photo.
Sethro
- Joined
- Feb 9, 2010
- Threads
- 41
- Messages
- 333
Did the front power seats work? I need the front mechanical adjustment bars for both seats that adjust the seat sliders." The white plastic housing and rods and motor across the front of the seat to the other white plastic housing on the other side of the seat on both seats. Are these still good? I also need a passenger seat bolt.
- Joined
- Jan 22, 2003
- Threads
- 276
- Messages
- 1,581
- Location
- flagstaff, Az , 86004
- Website
- www.adventuredriven.com
Any luck with my parts?
Sethro
Sethro
- Joined
- May 19, 2008
- Threads
- 61
- Messages
- 368
- Thread starter
- #91
Just sent you a PM.
Hi Nick, Sorry, no axles and no knuckles. Thanks, Tim
If you want the whole drivers seat then it's $25 plus shipping. I don't have a passenger seat. The drivers seat worked as far I as can recall the few days I drove the car. Bolts included.
Just sent you a PM.
the main truck computer is behind the glove box to the right, here are some photos of the other part I want. the ignihter is located to the right of the master shown in photo.
Sethro
Hi Nick, Sorry, no axles and no knuckles. Thanks, Tim
If you want the whole drivers seat then it's $25 plus shipping. I don't have a passenger seat. The drivers seat worked as far I as can recall the few days I drove the car. Bolts included.
Just sent you a PM.
- Joined
- May 19, 2008
- Threads
- 61
- Messages
- 368
- Thread starter
- #92
A quick note for those of you interested in buying parts.
Again, from the main add page go here --> http://www.ksl.com/index.php?nid=218&ad=16280226&cat=656 to see some pictures of what parts I have available. I usually keep this add updated with current pictures or current as possible.
I try and sell parts as a whole instead parting off of parts, so for example...If I can sell a whole door or a tranny, or etc...rather than rip and tear it apart I prefer to do so. It's much simpler this way as a lot of times I have to pull the parts and don't make any money on doing this and I do it on my own time not to mention it was a high of 20 degrees here today. I also store the vehicle 20 minutes away from where I live, so I have to travel to where it's located.
Please be patient and know that I do have a full time job and am pretty good with turn around time and will work with you as best I can. Granted that it's getting colder outside and the snow is flying I prefer to spend less time outside pulling parts, so if it's something that you are interested in and can wait until Spring, then great, otherwise, just know it may take a little longer to get the parts. I've also had a lot of request to pull parts, and once I get them pulled, I sometimes never hear back from the person requesting the part. If this is you, then don't request parts from me.
Yes, I realize this is one of the many aspects of parting out a vehicle, and if you all lived closer I would be happy to let you go after your own parts as I have done with others, so with that said...thanks for hearing me out...(yes, I'm whining, a little).
Thanks to my fellow mudders for your support.
Cheers,
Tim
Again, from the main add page go here --> http://www.ksl.com/index.php?nid=218&ad=16280226&cat=656 to see some pictures of what parts I have available. I usually keep this add updated with current pictures or current as possible.
I try and sell parts as a whole instead parting off of parts, so for example...If I can sell a whole door or a tranny, or etc...rather than rip and tear it apart I prefer to do so. It's much simpler this way as a lot of times I have to pull the parts and don't make any money on doing this and I do it on my own time not to mention it was a high of 20 degrees here today. I also store the vehicle 20 minutes away from where I live, so I have to travel to where it's located.
Please be patient and know that I do have a full time job and am pretty good with turn around time and will work with you as best I can. Granted that it's getting colder outside and the snow is flying I prefer to spend less time outside pulling parts, so if it's something that you are interested in and can wait until Spring, then great, otherwise, just know it may take a little longer to get the parts. I've also had a lot of request to pull parts, and once I get them pulled, I sometimes never hear back from the person requesting the part. If this is you, then don't request parts from me.
Yes, I realize this is one of the many aspects of parting out a vehicle, and if you all lived closer I would be happy to let you go after your own parts as I have done with others, so with that said...thanks for hearing me out...(yes, I'm whining, a little).
Thanks to my fellow mudders for your support.
Cheers,
Tim
Last edited:
- Joined
- May 19, 2008
- Threads
- 61
- Messages
- 368
- Thread starter
- #93
Sorry, no headlights or grill.
- Joined
- Feb 9, 2010
- Threads
- 41
- Messages
- 333
I will take the seat assembly for $25 plus shipping. Can you take off the seat slide adjustment assembly with motor and just ship that? The rest is not needed......
- Joined
- May 19, 2008
- Threads
- 61
- Messages
- 368
- Thread starter
- #96