wiring

Howdy all, Doing some troubleshooting of why my trailer light harness isn't working, I came across the weirdest thing. I found whoever put in the wires cut about 1/4 inch of wire from the original trailer wire harness, P/N 00526-00930, for what appears to be the left hand turn signal wire. I'm...

Anyone have any experience fixing a melted / corroded wiring harness connector? I was chasing down some trouble with my rear taillights on my FJ60 and fixed some problems then found more. The blue connector from the main harness to the rear harness has a corroded / melted pin and I need to...

I'm replacing the stock tail lights on my '66 because they are buried by my new bumper/tire carrier. There are only two wires and the wiring diagram that's from back then also shows only two wires. How do you get tail lights, brake lights and turn signal out of two wires? The wiring diagram I...

So I picked up a trashed 95 with lockers just to remove the lockers to rebuild for my 94. So I want to take the entire axles and wiring to complete the changeover. Now from what I've read I need the harnesses coming from the axles, the computer in the rf kickpanel, the switch and there is...

I recieved my ewd this week, holy crap this is nice i don't know how i made it through life without it.

I'm interested in fabbing and mounting some aftermarket switches for lights, compressors, radio power etc up here and I'm curious if anyone has taken it on? My initial hope was that I could somehow use the existing g wiring that's in place. If not, where have you mounted aftermarket switches?

A pair of wires in an heavy sheathing that go through the floor directly under the driver's seat (see pic). My FJ is full smog and I'm thinking maybe O2 or cat sensor? Someone has cut them off underneath the vehicle and I want to either reconnect or remove...

x

Hey y'all, I could use a little help with the wiring involved with starting my '72. I tried searching but can't seem to really find what I need, so I'll just have to ask. Several weeks back, the original starter crapped out on me. Everywhere I looked seemed to recommend switching in a GR from a...

I purchased a set of aftermarket turn signals for my FJ45 project. The wire colors do not correspond to any published diagrams that I have found: Red with blue stripe Green with yellow stripe Green Any ideas on which is ground, running and turn?

When it comes to repairing a wiring harness, would you prefer to: 1. Splice in a short length of new wire by soldering. If the problem is at the connector, crimp new pins and new connector. Use heat shrink tubing to seal it up. 2. Replace the entire length of damaged wire, crimp on new pins, and...

I'm trying to figure out how to wire my 69 fj40 to tow a trailer. I searched but only could find one other forum about this and it was for a 1980 which has different tailights then mine. I think I could probably figure out which wires to tap into but I don't want to hack up my harness. So what...

Looking for a full set of 2UZ engine wiring harness plugs... or maybe a full harness. mark

I'm looking for all of the plugs that connect to a 2UZ engine. Is there a source for these? mark

Replaced tie rod ends and a few other things so the truck was in the driveway up on jack stands for less than a week while I ordered some parts online. Finished the job then popped the hood just to inspect and found chewed wires. The chewed wires are all connected to the "black box" thing...

I pulled off my steering column cover to replace my ignition cylinder and noticed one of the soldered wire had broken loose. Can I solder it back on without buring the plug or am I looking at a replacement?

so, tried search, apparently I can't find the wright words for the search. I want to upgrade the headlight wiring to bigger wires to get max performance. I keep hearing about the headlights being wired differently than "normal" cars. Anyone got a wiring diagram or good explanation of what I...

So now that we have the LC running I checked the check engine light and got an error code 28 No.2 oxygen sensor/heater signal fault. I went to go look and see if there was anything obvious wrong and low and behold I found this.. Looks like someone or something has cut\chewed through the O2...

I'm looking for factory amp plugs with a little wiring on them. I want to build a test jig and see if I can fix my factory amp (if I can find it, I seem to have misplaced it. It's tough trying to figure what goes where when all I can see are the pins on the amp plug. If anyone has a set they...

My 1968 needs a wiring harness. I am only interested in an OEM one. Does not have to be perfect.