wiring

I'm hoping one of you electrically inclined types can help me out here. I'm in the process if installing a VIAIR on-board-air system in my rig and thought about adding an electronically controlled purge valve to the system for 5h!ts and giggles. I'm planning to use this momentary switch to...

I'm hoping one of you electrically inclined types can help me out here. I'm in the process if installing a VIAIR on-board-air system in my rig and thought about adding an electronically controlled purge valve to the system for 5h!ts and giggles. I'm planning to use this momentary switch to...

Hello all, I am planning a couple of trips this summer. I will be trailing a 2k lb pop - up about 50 miles each trip. Does anyone have suggestions as to what brand of hitch and wiring harness that is the easiest to install and not too expensive? I would like to get a class III something like...

Hi all, While I've been doing oxy-acetylene welding for a while, I'm newer to MIG welding. Bought a relatively cheap Lincoln 125 last year from the Home Despot, expecting that I would be able to convert it to true MIG rather than the (what I now realize is messy crap) flux-core. I looked at the...

Anyone know or can point to the proper routing of wires for a rack mounted lightbar? Pretty clear the grommets allow wires to be run into and down the rack to channels in the roof, down a corner pillar under thr trim; but from there where do the OEM wires head? Into the engine compartment or...

Not sure if this is a lost cause but I am attempting to replace my current toggle switch for the hazard lights with a OEM Toyota pull switch. Where do I begin?? The PO installed the toggle switch and I have not a clue to where to begin. Maybe someone out there can give me a starting point.

Has anyone got a copy of this page for the diesel engine?

i had thought the license plate bulbs were out on the new to me 81 BJ42 i am fixing up so when I took the plate holder off to refurbish and paint, I replaced the bulbs, yeah they were toast but no. new ones didn't fix it got underneath to look at the wiring and lo and behold the wires that...

I've looked around and haven't been able to find a thread about installation of OEM fog lights on an FJ40. Which surprised me, because if you are looking for 40 parts online it's hard not to find an add for OEM or replica fog lights. Does anyone have any information on the correct placement of...

I am installing a new wiring harness in my 71 FJ40. I need to know if I can install a fuse able link in-between the voltage regulator and the fuse box. The + feed comes from the voltage regulator directly into the fuse box (different from the original factory harness). I had an issue where my...

I have a full wiring harness off a 1986 FJ60. $175 plus $25 to ship anywhere in the lower 48 via UPS Ground PM me for more info Quite a few pics here

I need some help. I've read over all the forums and I'm still a bit stuck. My fuel gauge always shows empty. Following the advice of many others I started with the fuel sending unit. The unit itself is fairly new and with a multimeter it registered about 16 ohms on full and 119 ohms empty...

Stereo Wiring: Land Cruiser / LX 470 (1998-02) Does anyone have any idea what pin size could be used to solder on to the aftermarket source create an adapter harness? I dont want to chop off the factory one since id be soldering the wires anyway, id rather to that on the bench. Can i splice...

I'm replacing the cobbled up wiring for my 1978 converted to 3FE. Hopefully when I get all my questions answered, this can be a resource for others tackling this conversion. What I know for now is that the engine harness goes in with no modification. I'm trying to modify my cowl/firewall harness...

I bought a replacement indicator and they're not exactly the same. Does any have the picture of the wiring and description off what each does? I can't seem locate it. The last lic is the newer one and it has 2 extra wires that are confusing me . Thanks

Like the title says, I'd like to replace the awfully spliced and POed wiring harness in my 78 FJ43. I need a decent engine and interior harness for a 78 or other applicable years.

I have a brand new wiring harness that I no longer am going to use. I purchased it for an engine swap project and the guy backed out. It is a stand alone harness for a Gen IV/ 6L80E or 6L90E trans. This will fit any of the 2007 to current truck engines with or without active fuel managment and...

I just bought an ARB 50 qt. fridge and I'm trying to figure out my wiring. I currently have an AWG 8 wire run from my starting (only) battery to the driver's side back panel and an Alpine sub amp. I want to run the fridge on the passenger side, so I'm torn on how to wire things back there. I'm...

Hey all, I've been searching and googling this all weekend, so if this is in any way obvious, I apologize, but... I've blown some "fuse" in my 2003 LX470 that supplies +12v to the trailer battery lead on my factory 7-pin towing receptacle. Background: I have a camping utility trailer that I...

Hi, Today I wired my LED light bar according to the following diagram and using a demister button. My Idea was by using this wiring philosophy I run one less wire across the firewall and I get the high beam trigger signal before the dimmer relay. Why before the dimmer relay? I had problems...