spring

On a '97 4Runner is the spring on the fuel door available separately and replaceable? Have lost the spring on the fuel door and am unsure if the entire fuel door assembly must be replaced to have a functioning spring loaded fuel door.

whats the best advice for a little cosmetic rehab? Im planning on using my stock leafs in this picture. I was going to pull them off and paint 1. Should I paint as whole unit after some wire brush work 2. Pull them a part have them blasted and painted Road warrior rehab not a nut and bolt...

I'm relatively new Landcrusier owner. I'm learning about the wonderful world of rolling restoration, maintenance and stuffing mitts full of $100 bills into my BJ to fix things. Still love it. Just installed an OME suspension system and now see that my 81 BJ42 frame plates where my rear spring...

Final Agenda: Tuesday PM: · Travel to New Bern · Tryon Palace · Stay at the Courtyard in New Bern Wed: · Cedar Point Ferry at 10:30 AM – 2 Hr 45 Min ride · Check into Bluff Shoal Motel · Check out Ocracoke Thu: · Ocracoke to Hatteras Ferry ·...

I need to get some new rear leaf springs. The current ones are 43" long 19.5" from front to mid and then 23.5" from rear to mid. Problem is they are older and since i put the new engine in i am getting crazy axle wrap which has broken/loosened the c clamps for the springs. See exhibit A and B...

I hopped into my 2008 200 this morning and found the passenger floor mat containing a small reservoir. Not a huge amount of water but a cup or so approx. Closer inspection yields its dripping from above perhaps out of the HVAC or up higher? Glovebox is dry but plastic trim panel above the...

I need to weld some new spring plates on my doffs as the centre pin holes are ovals out. Can any tell me what the pin diameter is? Stupidly I cannot measure off my springs as I got rid of them. I suspect that the hole should be 19mm diameter?

I thought it might be a good idea to have a place where everyone could list the spring rates of various suspension kits you're all running for those of us in the market. If we could list the stock values as well that would be great. I see them listed in random threads...or maybe this already...

My trucks springs are flat. Truck had what I thought was an after market 2 inch lift. Bought light duty OME leaf springs and now catching hell getting them reinstalled. It is close but I can't get front of spring close to front shackle mount. Did I need to replace shackles? Adjust the...

Looking to replace my rusted out spring hanger brackets on rear of truck, I need forward set where spring bushing mounts onto frame channel. Only need front set on rear . thanks

83 fj60 carb internal spring. Seeing where i can find one

I have tried with no luck to find passenger side Seat spring does anyone have any Idea who or where to purchase one?? Thanks !

I have a set of 4 used spring spacers for sale. 2 for the front and 2 rear. 1 inch spacers. 80 Series Coil Spring Spacers - Man-A-Fre $65 shipped CONUS, $50 local pickup

Anyone running this lift? Is it level, do I need spacers for the front and are there any driveline issues? Thanks

Hey all. I'm new to the 4 link world. I would like your opinions on what direction I should go with my 1992 single cab. I tow a stramcleaner skid with a 200 gallon water tank with it. Currently IFS lift running 36" tsl swampers. 5.29 gears. I'm looking for the best riding, performing on and off...

I noticed a my passenger side front leaf spring stack has shifted - springs have moved so a couple of longer leafs are net stacked straight. I get an occasional clunk from the front leafs when cornering, and that got me looking at the springs. I have tapped them into alignment, but they will...

I am trying to figure out what sort of suspension lift I have on my '78. I believe it was set up with a very sturdy/stiff suspension, and since I am 95% on road driving, I would really like to soften it up. I don't know a lot about suspensions, but I know I have seen 3/4 ton trucks with...

Ok im thinking my spring bushings are worn out and im looking to replace them with same OME as they came with. My 2.5" kit is at least 10 years old. I have no idea of the model number of it so i have no idea what bushings to buy or are they pretty much standard from the different levels of OME kits?

15th annual Bako rally and swap meet Sat. April 29, 2017 8:00 Am to 2:00 Pm. At the North Bakersfield Toyota dealership near the corner of Hwy 99 and Merle Haggard Dr. Come and buy, sell, trade, browse, and hang out with fellow Cruiser heads. As always this is a FREE event. Sign in at Andy's...

It is that time of the year! Get the shocks or suspension you want for your rig!!! Check with your favorite retailer on pricing. See below for hints and the link! Tips to Ensure Timely Processing of Rebates: Carefully review all Terms and Conditions on the back of the rebate form. Check that...