pressure

Hi. Iv got a 1990 HDJ-81 With the 1HDT. How do you get the oil pressure sender out? I need to replace it. Is there a trick to this or do I just need smaller hands? Any help would be great. Thanks. Michael

Hi. Iv got a 1990 HDJ-81 With the 1HDT. How do you get the oil pressure sender out? I need to replace it. Is there a trick to this or do I just need smaller hands? Any help would be great. Thanks. Michael

I just got a 2000 LX and have an absolute mountain of preventative maintenance to catch up on before i get to neutral pressure adjustments. I have two small children who id rather spend my time with so i only get about 30 minutes of maintenance time per night after they go to bed so its likely...

in need of a pressure plate for my 2lte bought a automatic motor trans combo went to put it in my old 2L truck and the plate off my old one is only 6 bolts please let me know if you have one laying around 801-564-9029 Ryan

Yeah....I know, If its running and not knocking...its probably OK. But I just can't stand the factory gauge. After warm up, basically indicates ZERO (or right at it) at idle (650 rpm). It DOES rise immediately with engine rpm, but I'd just like to be able to see numbers instead of an indicator...

Hypothetically, if I was running a stock CT26 turbo at 11psi measured at the manifold and fitted an intercooler I would likely see a pressure drop if u measured boost at the same point. Let's say this drop is 3psi. My boost is now 8psi. If I use a boost controller to increase this back to my...

I'm adding an extra inline fuel filter and want to tap into the flare nut where it transitions from the hard line to the rubber line that supply's the original filter. Does anyone know the size, type and pitch of the thread that the flare nut uses? I'd like to order all the adapters I need...

Found answers in other forum area. Thanks!

Hey, my dad recently got a 2017 Tundra with BFG ATKO2s in 275/65R16. The dealership inflated them to 34 psi, but I seem to remember running my BFG ats at 60ish. The max is 80 psi on the tire, for a much larger truck. What should he run his tires at? There's still snow and ice where he lives if...

What is minimum Tire Pressure can be run on FJ40 with 35s MT tires on 17" rims (315/70-R17)? What would be recommended tire pressure? I have been searching the web and forums, but what I get allot is recommendations for Jeeps on 15" rims. Many runs 10-12 psi on 31s and 33s with 15" rims on...

Hi Everybody, I don't post much but look at all posts for anything that I feel may help me. The wagon has done 438000 k's, has been converted to duel fuel (LPG and Petrol) and does not burn any oil between oil changes at 15000 to 20000 k's. I use Nulon fully syn 10-40 free flowing oil. On start...

I've searched, but apparently one code can mean a bunch of things. When checking my AHC, I got these two codes: C1712 C1776 I know my tire PSI sensors are messed up, which one of the codes. No biggie there. But I am finding a handful of reasons for code C1776. Does anybody have experience...

Infamous "wooosh" when opening gas cap filler. This is a " big wooosh" and just a "little wwooosh"!! Cannot sense an operating issue but obviously an issue none the less - 1. Can I reverse the lines going into the canaster? OR 2. Can I unhook the input and output lines. Attach a small filter (...

Has anyone gone to great lengths at setting up a heated high pressure wash station outside of their garage? I'm talking about using 120/220vac for heater, pump and permanently plumbed in cold water. Basically set up the station on one corner of the garage and then run the hose through the wall...

I started noticing my oil pressure gauge complete dead about four months ago, took it to a trusted Toyota master technician, he replaced the solenoid sender, worked for a day went bad again, took it back, he completely cleaned out the instrument panel and cleaned the circuit board from minor...

1997, 3.4L v6, automatic in a 1995 4Runner. 4x4. Notice my oil pressure was low. This picture was taken after it was very warm, rolling between Jeff City and Independence. On start up, pressure is higher. At least above the lowest hash mark. What could it be? I'm thinking an oil pressure...

Searching the forum I can't find any posts describing this condition. '96 FZJ80, 1FZ-FE, 210,000 miles. This is a recent development. On cold start (temps around 40F) I'm registering nearly zero movement on the oil pressure gauge. After warmup (coolant at full operating temp) oil pressure...

Good evening guys. This is my current situation with my 2000 LX470. A while back, I had someone replace the front control arms. The replacement ones are aftermarket. When it was time for me to pick up the LX I noticed that it was leaning more towards the driver's side. They "adjusted" the...

I have a '99 LC. I read somewhere that someone makes a special bolt for one of the fuel rails that has a schrader valve installed so a pressure check can be done. Does anyone have any info on this.

I have been looking at 3B threads regarding where to tap oil pressure/oil feed from for a turbo. at the moment all i want is a second oil pressure gauge and future oil feed. a lot of threads are for 40 series where access is available to the factory blanked plugs forward of the stock oil...