I admit I don't know much about differentials, and I'm chasing down a Driveline vibration. Was hoping someone more knowledgeable could watch the and tell me if this is where my problem is, or if this appears normal.
symptoms are growling on deceleration, almost like a lawn mower.
After the...
I've had this humming noise on the highway, it starts around 25mph and just gets louder as I go faster. I just rebuilt the steering knuckles, so I know it's not a wheel bearing, at least in the front. It doesn't seem to make any more or less noise going around corners. I just removed the rear...
Hi guys,
Does anybody can tell me the Size of the inner and outer pinion bearing and oil seal of a bj73 fullfloater rear diff?
Thnx a lot for your help!
Grz from holland
I have a '99 LX470 with 215K miles where I've converted the hydraulic ride system using a Strutmasters conversion kit. Did this conversion in the fall of 2014 (very improved ride). Most all my driving is highway with an occasional pulling my utility trailer or trailered drift boat.
This last...
After years of surfing this site as a guest, I finally joined. . . .
I have a complete set of NIB parts from JustDifferentials.com for replacing the front gears (4.10) in my 1993 FJ80 (with front e-locker). I bought the parts a while back, but I didn’t end up needing them. I could use the cash...
Moved up to 5.29 r&p on my 96 lx450 with about 210k miles. I had bought the rig from an elderly couple that were the original owners, and it was in stock condition when bought. So most likely "easy" miles.
$40 each set plus shipping or make me an offer
Arroyo Grande, CA
To ih8mud members in Utah: I need a referral for getting my new lockers and ring & pinion installed in my FJZ80 3rds. Can anyone recommend someone that does a great job for a fair price? I can take the 3rd anywhere along the Wasatch front. Thanks in advance.
Last night while doing all my Pre-Cruise Moab checks on my truck I noticed a very slight amount of up/down movement at the pinion flange on my front diff.
The diff has 4.88 Nitro gears and install kits from @justdifferentials that were installed just last summer, so I'm a little surprised to...
These are still new in the box. Thought I'd need them but the diff turned out to be fine.
DIFFERENTIAL OVERHAUL KIT FJ40/55/60, F&R applications, 45mm carrier bearing
Toyota Land Cruiser 9.5″ 4.10 Ring & Pinion by NITRO
Toyota Land Cruiser 9.5" 4.10 Ring & Pinion by NITRO
Purchased for $400...
This might be old news but after installing a OME 850s and 860s with no caster correction I decided to measure the driveshaft and pinion flange angles to check u-joint alignment. It seems those Toyota engineers knew what they were doing, even raised 3 inches the u-joints maintain nearly perfect...
Would this worn rubber bushing have anything to do with rack and pinion? or is it only holding front diff?
I'm trying to diagnosis skid control coming on like it did before replacing rack and pinion.
I just got my differential back. Before I put it in I noticed that there was no paint on the ring. Should I be worried? I always thought that the paint on the ring was used to show that the pinion was running centered on the ring.
There is no paint to show where it is running.
Should I be...
Hello everyone, as you can see fro the title my rear pinion seal is leaking. Oil is running out where the drive shaft connects to the diff and its no small amount, but not to where I cant keep the level up.
I have been searching the forums for ways to fix it and there are two drastically...
So I managed to break my front axle ring and pinion (more info in the link)
REAL TIME help , something snaped and out of town
I have already contacted ZUK (great guy !!!), but I am wondering if there is a shop in the DFW area that you would recommend for the task ?
I'll be removing the third...
Anybody knows if the pinion flanges on an 80 series are interchangeable?
I do know the rear diff is 9" and the front is 8" and the DS bolt pattern is different too, but will the rear pinion flange bolt up to the front differential ?
TIA
Hey all - Looking to swap out my ring an pinion from stock to 5.29. Around town driving on 35's is killing me. Had a few questions I was looking for advice on.
Is 5.29 really going to top me out at around 65mph/3000rpm? I don't do a ton of interstate driving, but trips to trails will be a bit...
Hi, Guys!
Sorry if this has been answered before, and I've looked through and contacted a couple listed shops from the site, but wanted to ask as I've received a couple quotes I thought were too high.
I've got 100 series Land Cruiser. I have a rack and pinion sitting in my house that needs to...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.