help

I have been driving my 2000 100 Series (201k) for about two years now. My dad actually bought the truck brand new back in the day and I took ownership as my daily driver after college. Decided I am going to go with the Ironman or ARB bumpers for my first modifications. Two questions - 1. If...

Have been struggling with this for three days on and off. Nothing on line, even in the Toyota van tech forums. Trying to find the low side port to charge my AC system. I have found the stickers where it has been converted to 134a. I figured the stickers would be close to where it gets charged...

Hey all, I don’t post on here a ton as my FJ62 is is many pieces and I’m slowly rebuilding. I am getting to the point where I can’t find a solid lead on a gen 4/6l80 combo anywhere. Most reasonable donors are more expensive than. FB marketplace “ran fine when I pulled it” are sketchy. Anyone...

On a trip from Calgary to Alaska and my 2003 LX470 started the N to D and N to R clunk. Not super bad, but worse when hot. Read all we can with limited cell signal, so have seen the common causes. Question is what are our odds of making it 2000 kms? And second, can I disconnect the drive shaft...

Help please! I have purchased a LX 450 97. I would like to replace the driver side rear corner bumper but I need the mounting brackets and assembly. I know the bumper cover is different in the LC than the 450 but are the brackets and assembly the same? I’m hearing different opinions. Also I...

Anyone have a rear end carrier 3:73 gears for a FJ60?? Just lost my pinion gear! Removed the rear axle but the pinion gear is binding. Can’t move Anyone close let me know! 310-717-4306 Jorge

My daughter has our 80 in Annandale, VA just outside the beltway. The LF wheel began smoking and its birfield grease on the inboard surface of backing plate. As routine maintenance, I added grease to the plug about 500 miles ago, checked tightness of the 4 lower knuckle nuts and left town. Then...

Hey gang. I paid someone to retrofit some HID projectors into my 2002 headlamps, and they didn't do a great job. In fact, they did a really, really bad job. Aside from a half-melted tab and scratched shrouds, the headlight housings no longer adjust up and down, OR right and left. I suspect it's...

Hello, I need help with the wiring diagram of this ECM from a 98' LX470. Specifically I need to find Knock sensor bank 1 KNK1 and Knock sensor bank 2 KNK2 wire. I've searched around manuals online but to no avail. any help would be greatly appreciated.

I’m chasing down a no A/C issue on my 2006 LX470. Previous owner mentioned that there was “an ac leak under the hood”. Foolishly at the time I figured it would be an easy fix and didn’t ask where the leak was. Now I’m working on fixing the AC and can’t seem to find any leaks or bad lines...

Hi everyone, Hoping to get some ideas on what may be causing this grinding noise which seems to be coming from the transfer case area. The truck is a 1979 BJ40 with a 4 speed transmission. The noise occurs in all 4 forward gears (while moving) and does not occur in reverse. When the clutch is...

Hello all. Looking to buy myself a 200 series and found one here locally (semi at least, 3hrs away) 2011 with 107k. Asked for some photos of underside but only got a couple. Wondered if it’s worth pursuing based on your guy’s opinions. 1 owner. NY owned. Carfax clean. Only things on there...

I purchased a parts 40 a while back, and it had these, what appear to be, lift springs in the back. They look pretty much brand new, so I would like to use them, if they are descent springs, and in the 2.5" range. I searched the part # and it looks like they may be pro comps, but the yellow...

Hello, getting a 98 here soon, and I'm wanting to upgrade the wheels from the generic style you see on most. I've searched quite a bit, but can only come up with websites in Australia offering a similar style wheels for a 100-series. Over there they're listed as 17X8, and I've seen some US...

Hello! I am trying to plan my air conditioner setup but I just don;t get electricity with the amps etc. People have explained it, but I just don't get it. Any help is appreciated. Looking at the under-mount AC (12V), which states: "System running 100% with 90°F Ambient Temperature =...

Hello can anyone help me a this, I redid my injectors on a 96 4Runner 3.4 and when I put plenums and all hoses on I saw this port on the back of the bottom plenum there was no hose and all hoses appear hooked up. I will attach pic of port and port location. It has vacuum suction when engine is...

Hello, I recently bought a 1983 BJ40 Land Cruiser 3b (3.4 litre) diesel motor with fuel injection. 4 speed original transmission. The previous owner said it was running really well last summer but they had an oil leak. Their mechanic decided to change the head gasket this spring and since...

I have an ‘81 BJ42 with a 13B. I believe I need to replace the main bearings but I need guidance how to identify the main bearing specs for correct replacement as well as where to locate preferably OEM main bearing replacements. I don’t know the month or year of the engine. Here are some...

If there is a better place to post this please let me know: Hey guys, I’ve been looking at getting a cruiser for a little while and I’m a bit unsure which would be best for me. Wondering if anyone can provide some advice or insight, happy to provide more info if it helps! Location: Australia...

for some reason my 80 randomly died out on the trail. Miles out of town in the back country in Kentucky. Thing has been doing great all day. Randomly died and won’t start back. Alternator is good. Tried to start back and then just lost it. Could use some pointers. I wonder if it’s the fuel...