gear

Trying to get through to change the clutch on a 77. I removed the two top bolts and 3 per side on the bell housing then with trans and t case (and engine) supported tried to wobble/force/move everything back. When I got frustrated with that, I disconnected the four bolts around the trans and...

I've got a 1994 FZJ-80. My buddy and I are doing the Mojave Road. It's ~140 miles off road from the Colorado River to Barstow, CA. I've heard 3 days is a good amount of time. Driving ~400 miles to get to the start and ~300 miles back. Tools: Good selection of sockets / wrenches, even my...

Hi All, My 86 LJ70 is popping out of 1st gear, which I assume means tearing into it. The syncros for going from 1st to second and second to third can be a bit grindy when cold as well. The truck has over 160k miles on it. Is this something I can do myself or have done in most garages or should...

Installing ARB lockers and a new Nitro 4.10 ring and pinion. I have gone from .020 to .005 pinion shim and the pattern doesn't seem to change. I've also experimented with the backlash trying to keep it between .006 and .010, how just to see how the pattern changed I took a pattern at .020...

After checking gear fluids in the truck, I realized it was a paramount concern to replace. Like everyone else, I decided to think about my options for fluids and after a trip to a few local places, I was shot down in my efforts to find GL4 for the trans/transfercase. Now I get it, the manual...

Help me out, who did the write up on fixing the wallowed out door gear. I have a couple that needs some love and was wanting to play with a fix. Thinking NicP, but can't remember. Thanks, Ron

so I've been doing a whole bunch of work on my land cruiser and i just put all new led's in the dash. when i assembled it i turned on the hazards to make sure they were working. when i did that there was a click in the safety lock for the gear shifter and every time the lights blinked the shift...

I'm about to tear into my case to part time it. I thought good opportunity to re-gear the t-case.. So I'm gauging interest to see if maybe a mass buy is possible for the Marlins gears. I would prefer the Marlin gears since they are made in Japan. Not knocking those of you who have the Trail Gear...

Everything you see in the pictures- Longfields (30 spline set) 6 Shooter knuckles Steering arms Bearings Trunion eliminators Studs wheel bearings It's pretty much everything you need to beef up your front axle. The Longfields alone are over $600. $900 for everything. Pick up in Las Vegas...

Correct me if I'm wrong.... With an open differential to determine the gear ratio: Raise both wheels off the ground, mark a tire, mark the driveshaft, rotate the tire one full revolution and count how many rotations the shaft makes. The number of shaft rotations = the ratio. Thanks Jim

I replaced steering gear with a remanufactured unit. It has taken the slop out of steering completely but the effort is considerably higher than previously. Not sure if it just needs to break in or if there is something wrong. Thoughts?

I happened to find this MalloMe gear (assorted cool stuff) on Amazon. They have great prices...and it seems to be good value as well. My latest find was a flashlight, very similar to the one I bought for nephew at Christmas for a heck of a lot more money. I got this kit, and loved it. I...

So I picked up a used ARB locker, I believe the model is an RD08. It is an older unit and uses a 1/8 BSPT bulkhead. I'm having trouble finding parts to connect the 3.5 mm line from the compressor to the locker. anybody have any recommendations? I called ARB and looked through their parts...

does anyone happen to have a 1fz-fe power steering gear they are willing to sell. if so please let me know.

I have a pair of 68k mile 4.10 geared differentials from my 1971 FJ40. They are in great shape - but have been sitting for 39 years in the axle. Reason for selling is I Pulled them to install 3.70 Diffs. Asking $200 for the pair Located in Scotts Valley, CA

I have this manual steering gear, free to anyone who wants to pay the shipping on it. It was working fine when removed from the truck for the PS mod.

Hi, I am sure this has been asked before but searching on the forum is not real good (even the advanced search) and it just brings up loads of completely irrelevant stuff. My son recently went to work os and gave me his precious 80 series. We have decided to do it up and keep it. However one...

Converting from a 3 speed to a 4 speed trans...keeping my 3 speed transfer...need the PTO spacer or gear for the 4 speed trans. Not running a PTO on this truck so spacer is fine.

Does the club sell a spare tire cover or "Trasharoos" with the ONSC Logo on them?

Just got a set of Gamiviti's plastic gears for the front seats. What type of grease should I use for the gears when reassembling?? I have gone through the installation procedures and @nakman 's thread on replacing them, but does anyone have any additional tips?? It seems pretty straight...