exhaust

FZJ80. AND FJ80 From parted out Cruisers: (Cats will include Vin numbers of cars removed from) 3FE exhaust manifolds, cats, some tailpipe sections. 1FZE 95 to 97 manifolds, down pipes with cats, down pipes without cats, muffler, resonator, tailpipe Sections. NOTE: LOCAL PICKUP SUGGESTED IN...

Are the manifold studs pressed or screwed in? Whats the best way to get this thing out?

I am a Ticketed welder Building custom 3" 304 Stainless steel exhaust kits for JDM Model 80 series with a 1-HDT motor. These kits are a full Turbo to Tailpipe solution for your 80 series coming with everything from Hangers, Hardware, Gaskets, Exhaust Cushions, Downpipe bracket, Etc to ensure...

Has seen better days, but still has both mounting tabs intact. $140 shipped

Need a f 2f Exhaust manifold. My performance manifold has a hole in number four pipe I'm sure with others to follow.

1F Exhaust manifold. $100 plus the ride from 49459.

Have an exhaust off of a 1973 Fj55. Cut right after the collector. Ok condition. Free for the taking. Dont want to cut it up and throw it away if someone could use it. Norcross/ Dultuh area of Atlanta.

My 2000 LX470 had an annoying rattle, which turned out to be from rusted out heat shields. They were in pretty bad shape, considering that the vehicle has only 150,000 miles on it. Screws/bolts were rusted up, so had to rip them out with pliers. Pic attached. Here are the replacement part...

As the title states. $30 shipped CONUS. OBO.

Anyone have a used turbo exhaust elbow from an FTE laying around(turns basically 90 deg to the rear and down)? I know I can buy new but hoping for cheaper/faster as used... TIA

I am reposting this from the other GX forum. Background: My GX460 serves as the daily driver, overlander, and future baby hauler, so noticeable drone was not an option. I looked at all the available bolt-on options (listed below) and decided none of them quite fit what I was looking for, so I...

Hey everyone I’m new here. Just purchased a 2001 Land Cruiser that has had a lot of modifications done to it. Even though it has the TRD supercharger, I am finding that when passing vehicles on the highway with the large gap between gears on the 4 speed, that its passing capabilities are lack...

After months of research I finally pulled the trigger on an 18” magnaflow muffler for my 19 sequoia. This seemed to be a conservative way to get a lower exhaust tone , a little more power, and minimal drone. All I did was swap mufflers. The drone at 1600 rpm is unbearable - especially with...

So recently my 97 seemed to gradually become more sluggish turning over. It always cranked but made me wonder if the cold weather was zapping the battery. Then it started idling rough when cranked. After a few minutes or putting into gear and gassing it some it seemed fine until I shut it...

I have the parts pictured off a refresh of my exhaust system. These are still serviceable and hate to just bin them. Would ship them out for $100 and shipping costs. Thanks, Eric

Does any one know of an aftermarket direct bolt on exhaust system from manifold back? Something similar to what OTRAMM used to produce? Looks like Toyota only sells muffler back. Mine is hanging on by a thread. I could take it to a shop but would like to install myself if possible. im also not a...

What is the exhaust manifold to down pipe flange bolt size and thread pitch on a 1979 fj40? TIA.

In fair condition. All hangers original and in place. You have to supply the rubber bushings etc. Small hole (dime sized) on top of the exhaust near the first resonator that you can have an exhaust shop patch up. Someone wants to pick up for scrap but want to see if someone can use it first...

Below is a TRI-MIL Header which I bought new. It was bare steel and I hit it with hi-temp fiz can to keep it from rusting. The project went a different route and it needs a Home. $200 and free shipping in the Lower 48 States.

Good morning all - Crawling around under my ‘94 tracing out fuel circuit and noticed the attached pinch on my exhaust. This is post cat, in the last run of exhaust before exit, right where it runs between frame and body. I showed this to my dad and he didn’t think it was a huge deal… to me it...