exhaust

I am going to start saving up to replace the entire exhaust system. I broke the front O2 sensor stud off over the weekend and the muffler brackets on mine have already rusted off. I would assume the cats are on their way out too. It looks like I can buy a complete new exhaust, manifolds all the...

Ceramic coated , planed/machined ready to install 3FE exhaust manifolds ready to install $500. Shipped to lower 48. Note: EGR port has been welded shut and shield bosses have been removed. I was going to use these on a 2F but couldn't get machine shop to thin the flange to match up with 2F...

Hello everyone, My 2012 LC200 (Diesel) has some annoying turbo lag. I would say that i have to wait depending on the current gear, between .5 and 1 second before the turbo engage. Furthermore i know that this diesel vehicule has a pretty limited exhaust gaz circulation due to the particle...

I'm trolling for ideas. I've narrowed down my exhaust rattle to the baffles in the muffler coming loose. It's about 18 months old and non-OEM. So far I have used percussive maintenance and crimped them in place by crushing the outer skin around them with a ball-peen hammer. But that's not...

My 80 has brand new OEM shocks and front springs. The hangers for the exhaust have been checked and are fine. Yet, there is still a squeaking that comes from underneath that sounds like metal on metal - i can't tell which side it's on and I know it's an old truck and will never be quiet, but...

Can anyone confirm if this is a Catalytic Converter or a resonator??? I have a 1992 Fj80 3fe my exhaust has definitely been changed as it differs from Oem It goes from exhaust manifold to down pipe (2 seperate pipes) to o2 sensors one on each pipe to a Y pipe right after sensors and go into...

Contact me with your needs. Cats will include the VIN number of the car it was parted out from. Down pipes are solid and exhaust manifolds intact. The parts are from a California Car so they meet the 50 state specs.

Hi, I purchased a new stock exhaust system for a 1977 Fj40 and was hoping for a picture of the hook shaped bracket that hooks into the two rubber donuts on the middle bracket. I've looked all over the site but not able to specifically see that part. Thanks.

I need to replace the entire exhaust system on my 09 LC200. Completely rusted out. Should I just order a full OEM replacement or cheaper / better performance with aftermarket?

Going to tackle my last (fingers crossed) exhaust leak on my 82 FJ 40 - Saudi Spec…any top tips for replacing these gaskets on the downpipe? I’ve read a thread about failures around the flange so I’ll have a look for any cracks. Any other tips are very welcome! Cheers

I want to replace my BJ40s (B engine) exhaust from manifold to tail pipe. Of course, no catalytic converter needed. I've called a few shops in town and they all seem to hover around $1200-$1500. Seems a little pricey, don't you think?

Hi there i have a 1991 lc80 with 1HD-T and have been trying to find a supplier for 3" downpipe/dump-pipe/turbo elbow to build my exhaust from, i would prefer stainless steel. 2nd question is what kind of sensors are you guys using for afr reading, and what location do you think is ideal? Also a...

Looking for an exhaust down pipe from a 2F engine. My application is a ‘77 40. In the DFW metroplex area. Let me know what you have

I need one of these, shipped to 28461. Thanks

I'm replacing my '94 exhaust with a '95-97 style from the manifolds back, but only one cat (and that is attached to the downpipe). I have the parts in hand except I need to weld up a spacer to replace the second cat. To make a spacer I need to grab some tubing (2-1/4"?) and two flanges. Anyone...

Looking for 4 exhaust valves for a 1KZ-TE top-end rebuild for my 1994 LC Prado KZJ78. Toyota Part #: 13715-67020. I'm finding it hard to track these down in the US - let me know if anyone has any leads!

Looking for 4 exhaust valves for a 1KZ-TE top-end rebuild for my 1994 LC Prado KZJ78. Toyota Part #: 13715-67020. I'm finding it hard to track these down in the US - let me know if anyone has any leads!

As all of you were at one point in time I am beyond amped about my 1st fj purchase. It is a '73 that was "restored" around 20 years ago with an aluminum body and fenders. It does not have any visible rust or bubbles. 350 was rebuilt and swapped in while keeping the 3-speed. It runs down the...

Does anyone know what the bolt size and thread pitch for linking the factory 2F exhaust manifold to the initial exhaust line flange? If anyone has the Toyota Part#, please share! Thanks!!

Hi there, my cousin gifted me his 91 Land Cruiser when he passed away last year. Do to logistics, and repairs, I just got it. The LC was in Montana, then hauled to Washington, then finally transported to my house in CA, I had a transmission, and new drive shaft installed before I had it...