exhaust

Looking for clean, functioning 1F exhaust manifold. Thanks, Jesse

So I have been at this for about a month now. Engine was running fine before and after replacement of valve cover gasket. About the third time starting up to move the truck the motor started running awful, white smoke and fuel leaking from the exhaust manifold to the point it puddles up on the...

fj60 exhaust doughnut gasket? Im in a rural town so I need to get any info the Napa guy can use. Last time we matched it up with some part. I failed to find an online manual and you cant trust the parts guy. Both napa and orilies sent me home with the wrong gasket. O boy o boy doughnuts.

hi tanks in advance for help and ideas. I am gonna build a exhaust system for my fj40 and I have never done one before. The headers I have on the 5.3 liter vortec are 2.5 inch flanges. Should I go dual exhaust or 2 into 1? If I go 2 into 1 should I upsize pipe ? If so how large should I go...

Landcruiser FZJ80 Series 4.5L Petrol 1990-98 - Full System - Genie Performance Exhausts Looks promising to me depending on how much shipping would be. Thanks, Cory

does anyone have a .stl file of the 2F exhaust down pipe flange? I need to get one cut. TY

Looking for options in the US for a replacement exhaust. Is oem the only way to go? New to this. Thanks for the help!!!!!!!

The PO of my rig had someone weld up a custom stainless steel exhaust setup. Does it look like the o2 sensors are in the correct locations?

Sorry, couldn't help but post this.... it's on Craigslist

I've got a V8 conversion and looking for advice/opinions on what direction to go on exhaust routing. Exit in front of rear tires, behind rear tires or out the back?

I had an exhaust leak between the front manifold and left/outer downpipe on my FJ80 so I removed the downpipe and catalytic converter. What a pain in the ass. I managed to trash the captive nut bracket that the cat-to-y-pipe bolts thread into and the rest of the hardware is in pretty sorry...

Some of you don't know that I'm sort-of a rebel. I don't take anybody's word for anything. I question everything. Convention should be challenged. I'm not an engineer, but I easily could have been. So, two decades ago when I installed my first Thorley header I followed the conventional thought...

1993 FZJ80 335k miles She has purred like a kitten for the past 23k miles since I got her. Yesterday the low oil light came on (she burns a fair amount, no leaks). I dumped a couple of quarts of Delo 15w-40 in and drove on. Today I pulled on the interstate and heard the noise below. I was on...

I recently added a kamar spare tire carrier and had to cut off the exhaust resonator to make it fit. This made the exhaust "whistle" louder. I finally ended up changing muffler and cat back system to 2.5". No more Whistle and I have noticed the car shifts up and down with more response. Used...

For sale, make an offer PM no cracks, good condition.. just need to be cleaned

Hey folks, My 97 fzj80 is at an indy exhaust shop today getting the over-the-frame exhaust job done. I went with the Magnaflow 23120 cat and a magnaflow muffler; going to see if I can reuse the tailpipe for now. Anyhow, the cat has one slot for the oem O2 sensor but, since I'm going down to 1...

I'm rebuilding a 3F motor and in the process bought a "full" gasket set believing all gaskets needed would be included. It does not have whatever it is that seals the two halves of the exhaust gasket together. In my limited experience of engines I have never seen a setup like this. Local parts...

I'm rebuilding a 3F motor and in the process bought a "full" gasket set believing all gaskets needed would be included. It does not have whatever it is that seals the two halves of the exhaust gasket together. In my limited experience of engines I have never seen a setup like this. Local parts...

My Y pipe has bit the dust, as well as showing symptoms of bad cats. I ordered The Magnaflow 23120 and the matching second cat and I'm hoping to install them later this week. Here's my question: What bolts do I need for the cats? Does the kit come with the ones that I need? Can I cut the heads...

Hi everyone I'm new to the forum from Ottawa Canada. I have a 91 LC 6cyl gas that was imported from Japan so it's a right hand drive. With all the road salt they use here the exhaust is completely rotted out and not weldable. I found a few direct fit replacements online but none of the...